Other than as a source of light, rays of light radiated from the car also became alert to other vehicles. However, if the condition is less good, when the rainy season can arise in the dew light car.
If you want to turn, reduce speed or stop, for example, a rider or winking light rays as a means to communicate with other vehicles. For that, the lamps shining car should be light. Do not dimmed a bit, especially out at all.
One cause of the light rays can interfere with the car is moisture. Although only a vapor, the moisture to sneak in the lamp can be with the car.
Besides dim ray emission from the bulb, dew or moisture can cause the bulbs drop out, especially if moisture or water vapor to the cables to trigger short circuit time dialiri electricity.
Therefore, try to check the lamp of your car. If there is dew or moisture in it, most likely mica and spools in conditions that are less good. While handling, with the gracious light cover, and to dry clean using a rag and spray with the air compressor or hair dryer (hair dryer).
For a more satisfactory results, we recommend to replace the mica and seals in car lamps with its a new. Seal less, in general meeting occurred because of the age.
The older age of the vehicle, the seal is generally less elastic (hard). Moreover, if the vehicle is often parked in the summer. The mica is so, the old age of the vehicle and the more often exposed to hot temperatures, the possibility of cracked or broken the greater.
***
Source : Translated from okezone.com
Prevent Axle Broken Suddenly
Flood ago jammed everywhere. Ah, that's enough torment. However will worsened when the road passes the damaged caused as the wheels suddenly broken.
This is a proof of the importance of caring for the drive shaft. Although the incident frequency rare, but appear to be making very. Impact not only on the owner of the vehicle, but also on all road users can cause congestion as long.
Drive shaft on the vehicles have a very vital function, namely to drive the vehicle forward or power from the engine that has been reductioned by gear and gardan. Energy is then forwarded to the wheels drive.
The vital part that must be on the drive shaft is a rubber (boots) fat cover on the connection to the drive shaft. This component must be examined from the possibility of leaks or torn.
If torn or leaking, the lubricant can be properly protected and outgoing long run will run out. When this section is completed without the lubricant, accelerate will Wear and tear on the its joints.
That is not less important, than to make fat out, rubber is torn or leaking can also invite dust and dirt entering. Dust and dirt can also accelerate the Wear and tear on the its joint.
When worn-out, danger is joints is separated from the holder. In fact, it is very possible as broken. So, try to note the rubbers before the possibility of leaks or torn.
How easy is that treatment with the conduct routine inspections every 10,000 km. When symptoms have rubber drive shaft start-cracked or cracked lubricant has begun to leak, replace immediately. And do not forget to use the drive shaft boots made from the original material is strong.
***
Source : Translated from okezone.com
This is a proof of the importance of caring for the drive shaft. Although the incident frequency rare, but appear to be making very. Impact not only on the owner of the vehicle, but also on all road users can cause congestion as long.
Drive shaft on the vehicles have a very vital function, namely to drive the vehicle forward or power from the engine that has been reductioned by gear and gardan. Energy is then forwarded to the wheels drive.
The vital part that must be on the drive shaft is a rubber (boots) fat cover on the connection to the drive shaft. This component must be examined from the possibility of leaks or torn.
If torn or leaking, the lubricant can be properly protected and outgoing long run will run out. When this section is completed without the lubricant, accelerate will Wear and tear on the its joints.
That is not less important, than to make fat out, rubber is torn or leaking can also invite dust and dirt entering. Dust and dirt can also accelerate the Wear and tear on the its joint.
When worn-out, danger is joints is separated from the holder. In fact, it is very possible as broken. So, try to note the rubbers before the possibility of leaks or torn.
How easy is that treatment with the conduct routine inspections every 10,000 km. When symptoms have rubber drive shaft start-cracked or cracked lubricant has begun to leak, replace immediately. And do not forget to use the drive shaft boots made from the original material is strong.
***
Source : Translated from okezone.com
Replace Spark Plugs, the Code and Specifications Notice
Form is small, but very vital role for the vehicle. Therefore, do not select careless spark plugs. If wrong, the vehicle engine ignition system you may be delayed. Note the code and specification.
Interference that occurs can be a small spark interest fire or even fireworks not spatter at all. Can also choose the wrong spark plugs cause symptoms of the occurrence of knocking.
Two things on the role associated with the spark plugs in the ignition system. Fireworks are usually small because the value of the major plug does not match that required in the combustion system. While knocking usually appear because of the fuel burning triggered by heat plug, not the vault fireworks. If this condition is left, after a long time will damage the engine.
Especially piston and cylinder engine in the cracks.
Errors in the plug is going to be possible considering the many false circulate plug in the market. Very difficult to distinguish them physically because of the original false and 100 percent the same. Therefore, if you want to buy spark plugs, the first suggestion is buy plug in official workshops.
That is not less important, note the code plug. This code determines the physical specifications such as spark plugs, great value detainees and hot plug the machine in accordance with their respective vehicles. Usually in the manual, the manufacturer is brand and inform the appropriate type of spark plugs. We live the instructions are.
In the manual also informed at the time to do a replacement. Reimbursement we usually have to do every 20,000 km or as much of two years. Except for spark plugs made of iridium material that can still hold up to 100,000 km. Meanwhile, the signs should replace the spark plugs, the power engine or the engine feels less stagnation felt.
Other marks are difficult to machine is turned on. Worn spark plugs are still in use would also result in emissions that will be much greater, so that when the emissions test, most likely your vehicle will not pass emissions test.
***
Source : Translated from okezone.com
Interference that occurs can be a small spark interest fire or even fireworks not spatter at all. Can also choose the wrong spark plugs cause symptoms of the occurrence of knocking.
Two things on the role associated with the spark plugs in the ignition system. Fireworks are usually small because the value of the major plug does not match that required in the combustion system. While knocking usually appear because of the fuel burning triggered by heat plug, not the vault fireworks. If this condition is left, after a long time will damage the engine.
Especially piston and cylinder engine in the cracks.
Errors in the plug is going to be possible considering the many false circulate plug in the market. Very difficult to distinguish them physically because of the original false and 100 percent the same. Therefore, if you want to buy spark plugs, the first suggestion is buy plug in official workshops.
That is not less important, note the code plug. This code determines the physical specifications such as spark plugs, great value detainees and hot plug the machine in accordance with their respective vehicles. Usually in the manual, the manufacturer is brand and inform the appropriate type of spark plugs. We live the instructions are.
In the manual also informed at the time to do a replacement. Reimbursement we usually have to do every 20,000 km or as much of two years. Except for spark plugs made of iridium material that can still hold up to 100,000 km. Meanwhile, the signs should replace the spark plugs, the power engine or the engine feels less stagnation felt.
Other marks are difficult to machine is turned on. Worn spark plugs are still in use would also result in emissions that will be much greater, so that when the emissions test, most likely your vehicle will not pass emissions test.
***
Source : Translated from okezone.com
Tip Sell Car / Second-Hand Motorcycles
If you intend to sell cars or motorcycles that are owned at this time, there are several things you should note that a vehicle can be sold with a satisfactory price. Here are some considerations that you can apply:
1. Find information about the list price of the car or motorcycle used as a benchmark market price. This way you can weigh, how reasonable the price offered from your vehicle.
2. Fix the damage that may have. With repair of damage that may have on your vehicle, it will increase the selling price. Because prospective buyers of used vehicles more cock that is still prime condition.
3. Clean and trim your car or motorcycle. Discard and drop all the things that is not important which is still on the stick to your vehicle. For example, waste, dust, dust, or even stickers and accessories are less suitable placement. Because some consumers choose vehicles that condition 'flawless' without a specific attribute or accessories.
4. Collect and complete the documents your vehicle. Prospective buyers will consider completeness and authenticity of the correct documents your vehicle. If you still have the completeness of care (service) periodically, it will increase the selling price of your vehicle.
5. Objective and honest to the condition of your vehicle, including weakness or damage. If there are prospective buyers who inquire about the condition of the vehicle that you sell, you should describe the fair, including weakness and damage that may have. Because so buyers can take into account how much improvement they may remove the vehicle after your purchase. And, most importantly, they do not feel lied by you.
6. Promote through advertising in mass media. If the campaign via the 'from mouth to mouth' it is less convincing to sell your vehicle. Should promote through advertising in mass media, for example, in okezone.
***
Source : Translated from okezone.com
1. Find information about the list price of the car or motorcycle used as a benchmark market price. This way you can weigh, how reasonable the price offered from your vehicle.
2. Fix the damage that may have. With repair of damage that may have on your vehicle, it will increase the selling price. Because prospective buyers of used vehicles more cock that is still prime condition.
3. Clean and trim your car or motorcycle. Discard and drop all the things that is not important which is still on the stick to your vehicle. For example, waste, dust, dust, or even stickers and accessories are less suitable placement. Because some consumers choose vehicles that condition 'flawless' without a specific attribute or accessories.
4. Collect and complete the documents your vehicle. Prospective buyers will consider completeness and authenticity of the correct documents your vehicle. If you still have the completeness of care (service) periodically, it will increase the selling price of your vehicle.
5. Objective and honest to the condition of your vehicle, including weakness or damage. If there are prospective buyers who inquire about the condition of the vehicle that you sell, you should describe the fair, including weakness and damage that may have. Because so buyers can take into account how much improvement they may remove the vehicle after your purchase. And, most importantly, they do not feel lied by you.
6. Promote through advertising in mass media. If the campaign via the 'from mouth to mouth' it is less convincing to sell your vehicle. Should promote through advertising in mass media, for example, in okezone.
***
Source : Translated from okezone.com
Wary, Not Normal Beep on Vehicle
Often you often notice that sounds out of your vehicle? In fact the signs of damage a car can be found from the emergence of noise-sounds that are not normal.
Well, what are the sounds is? Here's the list:
1. Voters in the buzz machine
Check van belt, may be too fast. Ignored effect only if this component can trigger does not drop out of the water pump and the working of Alternator (dynamo ampere) can cause engine overheating and Battery (battery) does not get the flow that will make a vehicle broke down. Conditions of abnormal van belt (too loose) can also cause other sounds, the sound chipper. Bad effect is the same as the van belt is too tight.
2. Voice drone on wheels
Usually occurs when the car start running at high speed (above 40 km / hr). Check the foots, especially bearing wheels and wheel. When the voice heard from the front, the examination must be conducted in the wheels front. May have been worn wheel bearing, or the surface of the wheels is not flat. It is not too impacted to the other, but the sound is quite comfortable.
3. Noise like metal on the front of the barge
Especially when passing through the damaged road surface (perforated). Check the foots, especially tierod and rod end. Likelihood of this component is worn (not more precise), giving rise to noise when operating.
4. Voters in the rough when the engine is turned on AC
Check AC compressor, there is the possibility that AC compressor bearing damage or oil compressor problem (no leaks). If the left will create damage to the compressor it self.
5. Sound like two rough metal collide
Especially when we jerk of gas. This case usually occurs on vehicles with rear wheel drive system. Check the propeller shaft (coupling), the possibility of cross-joint is worn and broken. In addition to voice rough, the car body can also vibrate too hard when the propeller shaft does not balance.
From now on, always on the alert sounds that came out of your vehicle.
(/ / ton)
***
Source : Translated frm okezone.com
Well, what are the sounds is? Here's the list:
1. Voters in the buzz machine
Check van belt, may be too fast. Ignored effect only if this component can trigger does not drop out of the water pump and the working of Alternator (dynamo ampere) can cause engine overheating and Battery (battery) does not get the flow that will make a vehicle broke down. Conditions of abnormal van belt (too loose) can also cause other sounds, the sound chipper. Bad effect is the same as the van belt is too tight.
2. Voice drone on wheels
Usually occurs when the car start running at high speed (above 40 km / hr). Check the foots, especially bearing wheels and wheel. When the voice heard from the front, the examination must be conducted in the wheels front. May have been worn wheel bearing, or the surface of the wheels is not flat. It is not too impacted to the other, but the sound is quite comfortable.
3. Noise like metal on the front of the barge
Especially when passing through the damaged road surface (perforated). Check the foots, especially tierod and rod end. Likelihood of this component is worn (not more precise), giving rise to noise when operating.
4. Voters in the rough when the engine is turned on AC
Check AC compressor, there is the possibility that AC compressor bearing damage or oil compressor problem (no leaks). If the left will create damage to the compressor it self.
5. Sound like two rough metal collide
Especially when we jerk of gas. This case usually occurs on vehicles with rear wheel drive system. Check the propeller shaft (coupling), the possibility of cross-joint is worn and broken. In addition to voice rough, the car body can also vibrate too hard when the propeller shaft does not balance.
From now on, always on the alert sounds that came out of your vehicle.
(/ / ton)
***
Source : Translated frm okezone.com
Changing a Car 4 Door Coupe
If see cars coupe (two door) is very beautiful. Sporty design very thick aura race. But apparently your car can also be created coupe model. Next tip of rumah modifikasi AutoArt.
"The most important note is the ease of entry and exit to the back seats," Wahyu Yulianto explained, Workshop Manager AutoArt when okezone found some time ago.
According to him, if you want to make the car a four-door coupe hocus-pocus into a car, access to the exit sign in the back seat must be unimpeded. "Usually, there must be 10-20 cm distance," he said.
After measured how knowledgeable street needed someone to go out into the back seat, then the distance is marked. The next step B pillars moved appropriate distance that has been determined.
When this process is complete, the simulation re-entry should be made out to the back of the chair. "To ensure that people with any body postures can be through," he said.
If you are sure the sliding pillar B is successful, then pillars note that the connection is changed. Disconnect must be really strong, because the role of B-pillar is quite vital for the car.
Connection problem finished, it's time to switch on the rubbers. "If the new door is so, note rubber," he said. Rubber is not stick thin or perfect, can cause the water into the cabin. "If the incoming water could be rust," Wahyu said.
If everything has been considered to be perfect, lived note putty back door that is now so with a body. "Behind closed doors, putty be smooth and completely flat with the body, though the connection with the body ga plasticity," he said.
How, interested? So, not more difficult to appear so that your car is not sporty.
(tons)
***
Source : Translated from okezone.com
"The most important note is the ease of entry and exit to the back seats," Wahyu Yulianto explained, Workshop Manager AutoArt when okezone found some time ago.
According to him, if you want to make the car a four-door coupe hocus-pocus into a car, access to the exit sign in the back seat must be unimpeded. "Usually, there must be 10-20 cm distance," he said.
After measured how knowledgeable street needed someone to go out into the back seat, then the distance is marked. The next step B pillars moved appropriate distance that has been determined.
When this process is complete, the simulation re-entry should be made out to the back of the chair. "To ensure that people with any body postures can be through," he said.
If you are sure the sliding pillar B is successful, then pillars note that the connection is changed. Disconnect must be really strong, because the role of B-pillar is quite vital for the car.
Connection problem finished, it's time to switch on the rubbers. "If the new door is so, note rubber," he said. Rubber is not stick thin or perfect, can cause the water into the cabin. "If the incoming water could be rust," Wahyu said.
If everything has been considered to be perfect, lived note putty back door that is now so with a body. "Behind closed doors, putty be smooth and completely flat with the body, though the connection with the body ga plasticity," he said.
How, interested? So, not more difficult to appear so that your car is not sporty.
(tons)
***
Source : Translated from okezone.com
Engine Brake on Automatic Car
May some people think, using the automatic transmission car (matic) sometimes even making. For example when you want to do engine brake.
In fact, the car engine matic Braking can still be used. Utilization Braking engine that can help save the canvas can be obtained with the brake to move the transmission lever to the position of a lower transmission (downshift).
There are several ways to make a car engine brake matic. After the tread brake pedal and the car speed decreases, slide the transmission lever from position D (DRIVE) to:
1. To position "3", or a function-OFF OVERDRIVE / OD transmission are still in use OVERDRIVE manually (by pressing the button O / D of the transmission lever). Transmission will down to third gear position, and will not be able to move into fourth gear.
2. Moving again to position "2". Transmission will down to second gear when the vehicle speed down quickly to below the speed of 90-80 km / hour. This shift makes the effect more powerful engine Braking.
3. Move to position "L". Transmission will down to first gear when the vehicle speed down quickly to below the speed of 40-30 km / hour. This position in the engine Braking the maximum obtainable.
Do it over a third in a sequence from the most high-gear to the lowest. The principle is similar to the manual transmission, engine Braking obtained with the transmission to shift to a lower. Speed figures mentioned above should be adjusted on each vehicle.
Indeed, the movement is so fast the car feels a bit startled. Braking marks this engine work. Surge is more we can reduce the speed with regard to the car when the transmission shift lever position.
For road conditions in the field on the climb or decline, engine Braking we can get without having to move the transmission lever position as above. To do this is to run with the vehicle's position on the transmission lever position "2". Position to make this transmission can not move from the position of "2" to a higher gear and engine Braking effect at the time we reduce the gas pedal pressure will be greater.
Or can also use the position "L" position when the vehicle is faced with the road or climb steep decline (for example, in the basement of building). At this position, acceleration of the teeth can only move on the position of gear 1 only.
However, the position of "2" or "L" should not be used for a long time. If you already are in the flat road, the transmission immediately move to position "D". This is to prevent the transmission of fluida experienced overheating and damage to the transmission.
***
Source : Translated from okezone.com
In fact, the car engine matic Braking can still be used. Utilization Braking engine that can help save the canvas can be obtained with the brake to move the transmission lever to the position of a lower transmission (downshift).
There are several ways to make a car engine brake matic. After the tread brake pedal and the car speed decreases, slide the transmission lever from position D (DRIVE) to:
1. To position "3", or a function-OFF OVERDRIVE / OD transmission are still in use OVERDRIVE manually (by pressing the button O / D of the transmission lever). Transmission will down to third gear position, and will not be able to move into fourth gear.
2. Moving again to position "2". Transmission will down to second gear when the vehicle speed down quickly to below the speed of 90-80 km / hour. This shift makes the effect more powerful engine Braking.
3. Move to position "L". Transmission will down to first gear when the vehicle speed down quickly to below the speed of 40-30 km / hour. This position in the engine Braking the maximum obtainable.
Do it over a third in a sequence from the most high-gear to the lowest. The principle is similar to the manual transmission, engine Braking obtained with the transmission to shift to a lower. Speed figures mentioned above should be adjusted on each vehicle.
Indeed, the movement is so fast the car feels a bit startled. Braking marks this engine work. Surge is more we can reduce the speed with regard to the car when the transmission shift lever position.
For road conditions in the field on the climb or decline, engine Braking we can get without having to move the transmission lever position as above. To do this is to run with the vehicle's position on the transmission lever position "2". Position to make this transmission can not move from the position of "2" to a higher gear and engine Braking effect at the time we reduce the gas pedal pressure will be greater.
Or can also use the position "L" position when the vehicle is faced with the road or climb steep decline (for example, in the basement of building). At this position, acceleration of the teeth can only move on the position of gear 1 only.
However, the position of "2" or "L" should not be used for a long time. If you already are in the flat road, the transmission immediately move to position "D". This is to prevent the transmission of fluida experienced overheating and damage to the transmission.
***
Source : Translated from okezone.com
Tips To Be Paint Car Remain to Clean
Taking care of car remain to be clean by cleaning regularly will make your car seen more clean and at the same time maintain paint at body remain to be good in a condition.
But how to go into effect your car body appearance when paint just finish jerky at your car body.
Shall know by that there is elementary several things which you ought to pay attention when you clean car with paint which is just have been done. Namely:
1. If your dusty car body don't once in a while cleaned to use feather duster in order not to chafed at car body paint.
2. Suggested to sprinkle clean water of car all body then dry by using "kanebo" which material soft so that quickly permeate water.
3. Labouring if you clean car body don't use car sampoo or other sampoo in range of time 1 months after painting. This treatment have to be applied because car body which is just in paint will destroy because containing chemical essence shampoo.
4. When your car body is hit by rainwater, immediately clean your vehicle with clean water durabel car to body paint.
Because storey level acidity of rainwater very high, so that can destroy body colour.
( ikh / ddn )
***
Source : Translated from detik.com
But how to go into effect your car body appearance when paint just finish jerky at your car body.
Shall know by that there is elementary several things which you ought to pay attention when you clean car with paint which is just have been done. Namely:
1. If your dusty car body don't once in a while cleaned to use feather duster in order not to chafed at car body paint.
2. Suggested to sprinkle clean water of car all body then dry by using "kanebo" which material soft so that quickly permeate water.
3. Labouring if you clean car body don't use car sampoo or other sampoo in range of time 1 months after painting. This treatment have to be applied because car body which is just in paint will destroy because containing chemical essence shampoo.
4. When your car body is hit by rainwater, immediately clean your vehicle with clean water durabel car to body paint.
Because storey level acidity of rainwater very high, so that can destroy body colour.
( ikh / ddn )
***
Source : Translated from detik.com
Tips Treatment of Tire
Vehicle may be luxuriant, lustrous body with flossy interior, but how if tousled alias bad tire do not maintained? just Conceiving is, if condition of tire we is not optimal, like is wrong of installation, imprecise wind pressure, until let flower attenuate.
It is better also if justly us follow of tips from tire producer from Japan namely Bridgestone. As biggest tire market leader, wrong nope our dong peep a little of tips.
First, to the problem of tire replacement. Replacement tire moment, suggested to chosen is same tire of size measure and its, but if differing, minimize have to be equivalent of its haulage with original tire.
Later Then, avoid usage of tire which do not of a kind. usage of different Type tire at is same axis can influence maneuver, braking and stability, caused by difference of tire form and characteristic.
Hereinafter hit tire wind pressure. Most problem of tire because of which is is one this, its imprecise wind pressure. This is Matter very is influencing of ride achievement and tire age, even can cause extravagantly of consume Refined Fuel Oil.
Hence, suggested to often possible check tire wind pressure and arrange tire wind pressure, only at the (time) of condition of tire still chilled.
Last, how save tire which do not wear. When save tire, avoid direct sunshine, ozone, dampness, made product from petroleum, and air temperature which uncertain.
So, about like that's tips take care of our vehicle tire. Because tire is one of the safety element at vehicle, don't there is compromise in the case of its treatment.
( bgj / ddn )
***
Source : Translated from detik.com
It is better also if justly us follow of tips from tire producer from Japan namely Bridgestone. As biggest tire market leader, wrong nope our dong peep a little of tips.
First, to the problem of tire replacement. Replacement tire moment, suggested to chosen is same tire of size measure and its, but if differing, minimize have to be equivalent of its haulage with original tire.
Later Then, avoid usage of tire which do not of a kind. usage of different Type tire at is same axis can influence maneuver, braking and stability, caused by difference of tire form and characteristic.
Hereinafter hit tire wind pressure. Most problem of tire because of which is is one this, its imprecise wind pressure. This is Matter very is influencing of ride achievement and tire age, even can cause extravagantly of consume Refined Fuel Oil.
Hence, suggested to often possible check tire wind pressure and arrange tire wind pressure, only at the (time) of condition of tire still chilled.
Last, how save tire which do not wear. When save tire, avoid direct sunshine, ozone, dampness, made product from petroleum, and air temperature which uncertain.
So, about like that's tips take care of our vehicle tire. Because tire is one of the safety element at vehicle, don't there is compromise in the case of its treatment.
( bgj / ddn )
***
Source : Translated from detik.com
Ride Careful of Rainstorm
Rain more and more often address Jakarta. Do not half the battle, rain is often accompanied by high wind making tree bough broken. Some oppositely topple giant baliho or bough.
Threat do not merely from the top (of), because from under water suffuse which creeping slow make car can under water even swallowing it in damage floods pond is parts of its mechanic.
At case park vehicle, can possible avoid to park below big tree which its breakable bough like "angsana" or bear fruit to ossify like kapok.
This matter to prevent vehicle born down upon tree bar which broken effect of rain moment wind flinging down or happened storm.
Use opportunity intentionally time to entrust to ride darling in farm park with hard roof as in in building. Besides obviating vehicle from borning down upon hardware, car will is peaceful the than floods pond.
If vehicle perforced to be parked open in place, use opportunity intentionally closing it with vehicle blanket from parachute materials which can make vehicle of avoid from hardware incision which fall to befall.
Park to manipulate.
If parking vehicle for brief time, striving in break even position or manipulate. Labouring tip of vehicle of flange up at outside to be facilitating You when have to evacuate vehicle.
If cannot help park in roadside, select choose higher level surface like "ruko" page yard or shop to anticipate under water vehicle when public road aqueduct bubble up.
Besides, selecting hard surface, for example asphalt, concrete, cor, and or stone heap. Don'T park Your vehicle at surface of land ground, because worrying land ground will shift or disappear when rain.
If later then vehicle perforced to be suffused You have to be conscious there are some part of vehicle can stuck because a.l rainwater. spark plug, injection fuel electronic (EFI), coil, distributor, and platinum.
Meanwhile alternator which if under water can cause bearing release voice cheep to be accompanied with electricity reduction.
Even if water mixed mud, machine earn death out of a clear sky.
Porosity irrigate from air filter, carburettor, air-hole (irrigate intake) can make damage piston when machine forced by life or walk.
Part of transmission also is obliged to be watched by because water can infiltrate to pass transmission atmosphere hole so that mixed with transmission oli. Symptom arising out is sound. At final condition, rusty gear.
To avoid this occurence, require to improve frequency pay a visit to workshop when the rains still happened. (Algth Putranto redaksi@bisnis.co.id).
***
Source : Translated from Business Indonesia
Threat do not merely from the top (of), because from under water suffuse which creeping slow make car can under water even swallowing it in damage floods pond is parts of its mechanic.
At case park vehicle, can possible avoid to park below big tree which its breakable bough like "angsana" or bear fruit to ossify like kapok.
This matter to prevent vehicle born down upon tree bar which broken effect of rain moment wind flinging down or happened storm.
Use opportunity intentionally time to entrust to ride darling in farm park with hard roof as in in building. Besides obviating vehicle from borning down upon hardware, car will is peaceful the than floods pond.
If vehicle perforced to be parked open in place, use opportunity intentionally closing it with vehicle blanket from parachute materials which can make vehicle of avoid from hardware incision which fall to befall.
Park to manipulate.
If parking vehicle for brief time, striving in break even position or manipulate. Labouring tip of vehicle of flange up at outside to be facilitating You when have to evacuate vehicle.
If cannot help park in roadside, select choose higher level surface like "ruko" page yard or shop to anticipate under water vehicle when public road aqueduct bubble up.
Besides, selecting hard surface, for example asphalt, concrete, cor, and or stone heap. Don'T park Your vehicle at surface of land ground, because worrying land ground will shift or disappear when rain.
If later then vehicle perforced to be suffused You have to be conscious there are some part of vehicle can stuck because a.l rainwater. spark plug, injection fuel electronic (EFI), coil, distributor, and platinum.
Meanwhile alternator which if under water can cause bearing release voice cheep to be accompanied with electricity reduction.
Even if water mixed mud, machine earn death out of a clear sky.
Porosity irrigate from air filter, carburettor, air-hole (irrigate intake) can make damage piston when machine forced by life or walk.
Part of transmission also is obliged to be watched by because water can infiltrate to pass transmission atmosphere hole so that mixed with transmission oli. Symptom arising out is sound. At final condition, rusty gear.
To avoid this occurence, require to improve frequency pay a visit to workshop when the rains still happened. (Algth Putranto redaksi@bisnis.co.id).
***
Source : Translated from Business Indonesia
Economize Consumption Refined Fuel Oil Taken Care Of Three Component
Various Fuel Oil increase of trigger price (Refined Fuel Oil) is true we have to respon by doing improvement in many matter.
If previously Astraworld give economical tips with ride friendly of environment, article following more focussed at treatment of component influencing Refined Fuel Oil consumption. That is, with interest pay attention condition 3 component of necessary for combustion system: spark plug, air filter and fuel filter.
Third this component have to be prima in a condition. Spark plug have to can spatter on good firework. While air filter and also fuel filter have to often cleaned. More than anything else if summer which becoming quicken dirty air filter because sipped dirt. Dirt also easy to patch at fuel filter because this filter undertake to prevent mix by dirt in fuel in order not to step into room burn.
If third do not work better or dirty in a condition, happened by the condition of the so-called imperfect by burning. Fuel which step into room burn do not entirely burnt used up. So that, if calculated, yielded by energy is machine incommensurate to secretory fuel.
That is why the condition of spark plug, air filter, and fuel filter which do not oke in the end cause Refined Fuel Oil consumption become extravagantly. Do not only that, Refined Fuel Oil which do not burnt mentioned will follow castaway with gas throw away. If car with condition of machine like this tested by emission, gas throw away sure nya very ugly. It is possible that, its emission exceed boundary sill which have been determined and in the end affect ugly to quality of our air.
Line of least resistance take care of third this component is always periodic service. Workshop mechanic will check and clean or change third mentioned component which (it) is true have have to change. Inspection also better be done if emerging machine symptom which is stagnation. Machine which chok up to designate Refined Fuel Oil supply to room burn is not fluent which is big possibility triggered by dirty Refined Fuel Oil filter. Possible also because one of the damage spark plug / death.
***
Source : Translated from CBN
If previously Astraworld give economical tips with ride friendly of environment, article following more focussed at treatment of component influencing Refined Fuel Oil consumption. That is, with interest pay attention condition 3 component of necessary for combustion system: spark plug, air filter and fuel filter.
Third this component have to be prima in a condition. Spark plug have to can spatter on good firework. While air filter and also fuel filter have to often cleaned. More than anything else if summer which becoming quicken dirty air filter because sipped dirt. Dirt also easy to patch at fuel filter because this filter undertake to prevent mix by dirt in fuel in order not to step into room burn.
If third do not work better or dirty in a condition, happened by the condition of the so-called imperfect by burning. Fuel which step into room burn do not entirely burnt used up. So that, if calculated, yielded by energy is machine incommensurate to secretory fuel.
That is why the condition of spark plug, air filter, and fuel filter which do not oke in the end cause Refined Fuel Oil consumption become extravagantly. Do not only that, Refined Fuel Oil which do not burnt mentioned will follow castaway with gas throw away. If car with condition of machine like this tested by emission, gas throw away sure nya very ugly. It is possible that, its emission exceed boundary sill which have been determined and in the end affect ugly to quality of our air.
Line of least resistance take care of third this component is always periodic service. Workshop mechanic will check and clean or change third mentioned component which (it) is true have have to change. Inspection also better be done if emerging machine symptom which is stagnation. Machine which chok up to designate Refined Fuel Oil supply to room burn is not fluent which is big possibility triggered by dirty Refined Fuel Oil filter. Possible also because one of the damage spark plug / death.
***
Source : Translated from CBN
Remain to Maintained Even Crisis
Economic crisis is true make confusedly everybody. Do not merely dizzy car owner, Seller car ATPM even also follow hard offer its merchanidise because credit facility follow sky.
You do not be dizzy progressively it is better progressively give attention and diligent take care of vehicle. Because with treatment, age wear spare part will be maximal.
One of the top-drawer component to be observed by the condition of spark plug, machine oil, oil filter, tire wind pressure and accumulator. Enunciated treatment and its easiest.
Treatment of spark plug, machine oil, and regular oil filter make effective refined fuel oil vehicle consumption. Third can be controlled when You do routine treatment change machine oil.
Workshop mechanic will check and clean or give suggestion to change third that component which (it) is true have have to change.
Like spark plug is claimed component can spatter on good firework, air filter whereas and fuel filter have to is often cleaned air to which step into room burn to free from dirt.
At oil replacement, don't because reason scrimp to make You sacrifice the quality of oli and buy cheaper product unknowingly its specification beforehand.
For example for the car of under 2004 using SAE Iubricant 30 owning high viscosity rate because can make valve sound and "tiktik" sound machine.
Because one of the lubricant function is lubricate and make cool machine. With this function, is expected by lubricant or oil can share intrinsicly in assisting machine activity in order not to too much inhaling fuel.
Accumulator is very important component in ignition system and or electricity. At many case, lack of treatment make low accumulator result difficult machine starter. Clear Easiest treatment is with watching quality and also amount irrigate accumulator. Must it irrigate accumulator always awake among level low line and ordinary level upper as described at accumulator box.
If under level low immediately enhance. Because, functioning accumulator water to assist to to make cool accumulator cell. If accumulator water decrease and do not is immediately added, cell in accumulator can become to metamorphose which triggering is short circuit.
Later Then check terminal at accumulator do happened corrosion. Corrosion can be cleaned with sprinkle hot water at its terminals. Boisterous cheque also positive cable bolt and negative its. Don'T forget to give grease or fat at terminal to prevent corrosion.
Tire is component which is easiest to be taken care of. Start from routine check wind pressure. Tire with less adequate pressure will cause hot easy to so that hairless quickly.
And balancing Spooring can become good choice. Besides making vehicle progressively, this activity is you Can exploit to check the condition of tire as a whole.
At car owner with tubeless tire generally often neglect to check surface of their tire. It is possible that there is object which is implant and do not realize during long. (algooth.putranto@bisnis.co.id)
Algooth Putranto.
***
Source : Translated from Business Indonesia
You do not be dizzy progressively it is better progressively give attention and diligent take care of vehicle. Because with treatment, age wear spare part will be maximal.
One of the top-drawer component to be observed by the condition of spark plug, machine oil, oil filter, tire wind pressure and accumulator. Enunciated treatment and its easiest.
Treatment of spark plug, machine oil, and regular oil filter make effective refined fuel oil vehicle consumption. Third can be controlled when You do routine treatment change machine oil.
Workshop mechanic will check and clean or give suggestion to change third that component which (it) is true have have to change.
Like spark plug is claimed component can spatter on good firework, air filter whereas and fuel filter have to is often cleaned air to which step into room burn to free from dirt.
At oil replacement, don't because reason scrimp to make You sacrifice the quality of oli and buy cheaper product unknowingly its specification beforehand.
For example for the car of under 2004 using SAE Iubricant 30 owning high viscosity rate because can make valve sound and "tiktik" sound machine.
Because one of the lubricant function is lubricate and make cool machine. With this function, is expected by lubricant or oil can share intrinsicly in assisting machine activity in order not to too much inhaling fuel.
Accumulator is very important component in ignition system and or electricity. At many case, lack of treatment make low accumulator result difficult machine starter. Clear Easiest treatment is with watching quality and also amount irrigate accumulator. Must it irrigate accumulator always awake among level low line and ordinary level upper as described at accumulator box.
If under level low immediately enhance. Because, functioning accumulator water to assist to to make cool accumulator cell. If accumulator water decrease and do not is immediately added, cell in accumulator can become to metamorphose which triggering is short circuit.
Later Then check terminal at accumulator do happened corrosion. Corrosion can be cleaned with sprinkle hot water at its terminals. Boisterous cheque also positive cable bolt and negative its. Don'T forget to give grease or fat at terminal to prevent corrosion.
Tire is component which is easiest to be taken care of. Start from routine check wind pressure. Tire with less adequate pressure will cause hot easy to so that hairless quickly.
And balancing Spooring can become good choice. Besides making vehicle progressively, this activity is you Can exploit to check the condition of tire as a whole.
At car owner with tubeless tire generally often neglect to check surface of their tire. It is possible that there is object which is implant and do not realize during long. (algooth.putranto@bisnis.co.id)
Algooth Putranto.
***
Source : Translated from Business Indonesia
Tips Treatment of Wiper
Ride is true require high concentration storey level particularly if going down torrential rains resulting rider view blocked by is rapid of rainwater The mentioned can endanger, more than anything else if component like wiper which do not function nicely. Whew! Something that can hinder view in front of cannot seen finely.
So, so that the mentioned do not happened at us, hence taking care of your car wiper in an optimal fashion, my vacate to check network activity, start by activating wiper with previous water spray, till perceive optimal work storey level and electromotor elasticity of its liquidator rubber.
1. Check electricity system which if control of network have been done and do not be found by oddity, whereas wiper movement remain to be slowgoing, hence biggest anticipation have to be addressed by at electromotor function. Have recourse dynamo workshop to improve repair damage of the electromotor.
2. If wiper sudden die, Don't be direct of panic. Check barbed fuse function with this wiper network beforehand, before anticipating other damage cause.
3. Clean wiper rubber each every you clean your car, so that protected from gravel and dirt which patch at rubber. The mentioned can result incision at resulted by glass is small gravel which patch at wiper rubber.
4. If require to enhance water soap sufficiently into tube irrigate wiper, the mentioned so that smooth the way wiper.
( Muhamad Ikhsan / ddn )
***
Source : Translated from detik.com
So, so that the mentioned do not happened at us, hence taking care of your car wiper in an optimal fashion, my vacate to check network activity, start by activating wiper with previous water spray, till perceive optimal work storey level and electromotor elasticity of its liquidator rubber.
1. Check electricity system which if control of network have been done and do not be found by oddity, whereas wiper movement remain to be slowgoing, hence biggest anticipation have to be addressed by at electromotor function. Have recourse dynamo workshop to improve repair damage of the electromotor.
2. If wiper sudden die, Don't be direct of panic. Check barbed fuse function with this wiper network beforehand, before anticipating other damage cause.
3. Clean wiper rubber each every you clean your car, so that protected from gravel and dirt which patch at rubber. The mentioned can result incision at resulted by glass is small gravel which patch at wiper rubber.
4. If require to enhance water soap sufficiently into tube irrigate wiper, the mentioned so that smooth the way wiper.
( Muhamad Ikhsan / ddn )
***
Source : Translated from detik.com
Rain is Not Barrier
To most car rider, rain weather really unpleasantly, because rain, more than anything else in big intensity, can bother journey. They is also claimed by neglectless extra in piloting car at the (time) of rain weather.
Risk the happening of accident at the (time) of bigger rain of course than glorious weather moment. There is two especial poin why accident risk at the (time) of rain become biggerly is. First, slippery public road and suffused is. Both, approach distance become limited because closed rainwater.
Therefore, for the rider of car have to can weaken moment emotion pilot vehicle at the (time) of rain. Following there are some tips which can be made by hold to car rider so that can drive safely and balmy at the (time) of going down rain.
• Investigation of tire
Because rain result public road suffused by water and is slippery, ascertaining Your prima car tire in a condition. Its meaning, wind pressure have to snugly, groove / tire flower have to in a condition goodness. If Your car tire have 'balded', better immediately change with newly. Is important to avoid car sliped / slip or float above water pond.
• Decrease of Speed
At the (time) of rain, rainwater will mixed with oil above surface walke so that make surface of road street become slippery and easy tire of slip. To avoid risk, I lessen speed of Your car.
• Handling of slip
If even also perforced to experience of slip risk, don't panic. Step on rem with normal pressure. Don'T step on finished rem pedal, because that thing exactly will make Your car of dockyard. Besides, striving to control to drive quietly.
• Keep distance
Performance put on the brakes downhill usually if wet by water. As a result, braking distance will become compared to longer in a condition dry public road. Besides, distance look into also more limited because blocked by rainwater.
Therefore, to avoid collision, You have to keep distance with car exist in Your car front. Farther apart better it is of course.
• Turn on front lamp
In a state of rain, it is better You animate front lamp. This lamp not even assist You see fogbound road street or rainwater, but also assist other driver see Your car. Even, if rain have too close, better animate hazard lamp.
• Heavy of rain, Stop
The rains usually will experience of a period of its top, where pour and rain intensity very high. Moment a period of rain top, distance look into among one other vehicle and vehicle will be very short. If natural You of matter a kind of this, better don't continue journey. Dropp it till rain alleviate.
• Parked in secure place
Desist even also don't promiscuously. Look for peaceful location. Avoid to park under downpour moment tree, is more than anything else accompanied by high wind. Because, very possible tree will fall down and befall Your car. If will more peaceful, park in mal or officeblock. (afriyan-to@bisnis.co.id)
***
Source : Translated from Business Indonesia
Risk the happening of accident at the (time) of bigger rain of course than glorious weather moment. There is two especial poin why accident risk at the (time) of rain become biggerly is. First, slippery public road and suffused is. Both, approach distance become limited because closed rainwater.
Therefore, for the rider of car have to can weaken moment emotion pilot vehicle at the (time) of rain. Following there are some tips which can be made by hold to car rider so that can drive safely and balmy at the (time) of going down rain.
• Investigation of tire
Because rain result public road suffused by water and is slippery, ascertaining Your prima car tire in a condition. Its meaning, wind pressure have to snugly, groove / tire flower have to in a condition goodness. If Your car tire have 'balded', better immediately change with newly. Is important to avoid car sliped / slip or float above water pond.
• Decrease of Speed
At the (time) of rain, rainwater will mixed with oil above surface walke so that make surface of road street become slippery and easy tire of slip. To avoid risk, I lessen speed of Your car.
• Handling of slip
If even also perforced to experience of slip risk, don't panic. Step on rem with normal pressure. Don'T step on finished rem pedal, because that thing exactly will make Your car of dockyard. Besides, striving to control to drive quietly.
• Keep distance
Performance put on the brakes downhill usually if wet by water. As a result, braking distance will become compared to longer in a condition dry public road. Besides, distance look into also more limited because blocked by rainwater.
Therefore, to avoid collision, You have to keep distance with car exist in Your car front. Farther apart better it is of course.
• Turn on front lamp
In a state of rain, it is better You animate front lamp. This lamp not even assist You see fogbound road street or rainwater, but also assist other driver see Your car. Even, if rain have too close, better animate hazard lamp.
• Heavy of rain, Stop
The rains usually will experience of a period of its top, where pour and rain intensity very high. Moment a period of rain top, distance look into among one other vehicle and vehicle will be very short. If natural You of matter a kind of this, better don't continue journey. Dropp it till rain alleviate.
• Parked in secure place
Desist even also don't promiscuously. Look for peaceful location. Avoid to park under downpour moment tree, is more than anything else accompanied by high wind. Because, very possible tree will fall down and befall Your car. If will more peaceful, park in mal or officeblock. (afriyan-to@bisnis.co.id)
***
Source : Translated from Business Indonesia
Peaceful Motorize Cheerfully of Rain Moment
Some people tell the rains top happened in the China New Year. Afterwards, rainfall will decrease which finally come to a full stop and change with entry of summer.
Still, nothing that dare to guarantee that after finishing of China New Year, the rains also will end. That its meaning, downpour potency and floods still there.
To motorcyclist, rain, more than anything else in big intensity which followed with pond irrigate in road street even generate floods, (it) is true become fearful bogey which is very is. Very rare of motorbike which can get away from water pond.
Therefore, motorcyclist expected by extra bewaring of if downpour ride moment. Following there are some tip which can be made by guidance so that earning ride comfortably and peaceful at the (time) of rain.
Animating next lamp, though rain do not too close. This lamp not even assist we see road street, but also assist other driver so that can see our position in road street.
1. Use raincoat. Better use clothes model and pants. Avoid usage of raincoat poncho model, because very is not peaceful used by moment ride motorbike.
2. Use shoe for the protect of foot from rainwater, nicer which is antiwater. You can also rain moment shoe case use which sold by many in marketing.
3. Ride motor slow-speedly to avoid the happening of waving water effect of cleft from next wheel.
4. Avoid to ride motorbike beside moment car pass water pond. Because besides can be hit by splash, also conduct motor will be unstable because hit by punching waving water generated by car.
5. Lessen speed caused by possibility of water can mixed with oil above surface walke and do not seen by You. Pond Oil result road street become slippery and can make tire become slip.
6. After passing water pond, don't be direct step on the gas, because felt concerned about by rem do not taking hold well if You have to put on the brakes suddenly. Less its put on the brakes because of wet rem canvas by water so that energy clutch decrease.
To overcoming it, try to depress next rem lever and behind little by little walked slow to dry hit by rem water canvas.
1. Labouring to take coolly when passing road street suffused by water. You have to extra bewaring of, you Don'T pass hole.
2. If rain too close, don't ride force. You Better just desist at the same time await rain alleviate.
(afriyanto@bisnis.co.id)
***
Source : Translated from Business Indonesia
Still, nothing that dare to guarantee that after finishing of China New Year, the rains also will end. That its meaning, downpour potency and floods still there.
To motorcyclist, rain, more than anything else in big intensity which followed with pond irrigate in road street even generate floods, (it) is true become fearful bogey which is very is. Very rare of motorbike which can get away from water pond.
Therefore, motorcyclist expected by extra bewaring of if downpour ride moment. Following there are some tip which can be made by guidance so that earning ride comfortably and peaceful at the (time) of rain.
Animating next lamp, though rain do not too close. This lamp not even assist we see road street, but also assist other driver so that can see our position in road street.
1. Use raincoat. Better use clothes model and pants. Avoid usage of raincoat poncho model, because very is not peaceful used by moment ride motorbike.
2. Use shoe for the protect of foot from rainwater, nicer which is antiwater. You can also rain moment shoe case use which sold by many in marketing.
3. Ride motor slow-speedly to avoid the happening of waving water effect of cleft from next wheel.
4. Avoid to ride motorbike beside moment car pass water pond. Because besides can be hit by splash, also conduct motor will be unstable because hit by punching waving water generated by car.
5. Lessen speed caused by possibility of water can mixed with oil above surface walke and do not seen by You. Pond Oil result road street become slippery and can make tire become slip.
6. After passing water pond, don't be direct step on the gas, because felt concerned about by rem do not taking hold well if You have to put on the brakes suddenly. Less its put on the brakes because of wet rem canvas by water so that energy clutch decrease.
To overcoming it, try to depress next rem lever and behind little by little walked slow to dry hit by rem water canvas.
1. Labouring to take coolly when passing road street suffused by water. You have to extra bewaring of, you Don'T pass hole.
2. If rain too close, don't ride force. You Better just desist at the same time await rain alleviate.
(afriyanto@bisnis.co.id)
***
Source : Translated from Business Indonesia
Clean glass, Happy Heart
This Year the rains is true disturb because water spot not go down as water poured from sky added by high wind, but at intervals with pertained Jakarta sun sting very extreme.
Condition of like this do not make only drop health of body, but also darling car of You, especially part of next glass which become place look into the condition of in the face of vehicle have, potency to have problem.
If next glass less is paid attention, dirt can will heap and ossify (crystallized) because rest of gas throw away from oleaginous other pollution result or muffler partake to stick in glass.
Various this content quicken glass process become blurly. Its problem, rainwater attack on the surface of teared glass fall because coherent dirt have formed soft coat and have compound to with glaze. As a result, water do not is easy to sweeped and finally stick in glass.
If this condition happened, activated by wiper rather than freeing surface of glass from water, infact will incise surface of glass making lamplight from front become phosphorescently.
Hence, this undesirable condition require to anticipate. First step is checking the condition of wiper rubber. If rubber have barst and fragible have to be changed direct. Better wear original rubber, because width and length have been adapted for by requirement.
Every in journey, don't forget always prepare reserve water and special mop so that can clean rear mirror for the car of which have no special Iiquidator. Ascertaining used by mop really free from dirt, new later then start to rub glass by turning around and is not be one way static.
Don'T clean direct glass under sunshine especially if cleaning glass with car soap or shampoo. Its section, chemical vitamin in shampoo will quickly permeate into glass pore.
Each Every adding water in wiper tube strive always mix special shampoo dilution of glass. For best result, shampoo and water in tube changed each month. (Algooth Putranto)
***
Source : Translated from Business Indonesia
Condition of like this do not make only drop health of body, but also darling car of You, especially part of next glass which become place look into the condition of in the face of vehicle have, potency to have problem.
If next glass less is paid attention, dirt can will heap and ossify (crystallized) because rest of gas throw away from oleaginous other pollution result or muffler partake to stick in glass.
Various this content quicken glass process become blurly. Its problem, rainwater attack on the surface of teared glass fall because coherent dirt have formed soft coat and have compound to with glaze. As a result, water do not is easy to sweeped and finally stick in glass.
If this condition happened, activated by wiper rather than freeing surface of glass from water, infact will incise surface of glass making lamplight from front become phosphorescently.
Hence, this undesirable condition require to anticipate. First step is checking the condition of wiper rubber. If rubber have barst and fragible have to be changed direct. Better wear original rubber, because width and length have been adapted for by requirement.
Every in journey, don't forget always prepare reserve water and special mop so that can clean rear mirror for the car of which have no special Iiquidator. Ascertaining used by mop really free from dirt, new later then start to rub glass by turning around and is not be one way static.
Don'T clean direct glass under sunshine especially if cleaning glass with car soap or shampoo. Its section, chemical vitamin in shampoo will quickly permeate into glass pore.
Each Every adding water in wiper tube strive always mix special shampoo dilution of glass. For best result, shampoo and water in tube changed each month. (Algooth Putranto)
***
Source : Translated from Business Indonesia
Accelerate with Comfortably
Roadway in Indonesia is currish murderer. young Old, woman and men, can be killed. So That Indonesian Vice President Jusuf Kalla grip victim number accident of transportation in tired roadway 30.000 people per year.
Its meaning, every year of roadway can kill 300 times more than Flu Bird virus victim which only reaching 100 people more.
Victim Accident of roadway do not recognize age, gender till religion. In roadway, who is even also can become victim.
The accident influenced by various factor, like accretion of is amount of resident which disproportionately with amount of addition of joint streets, weak of straightening of and law applying of order related to vehicle security and usage in road street, and also still loosen road street consumer society discipline.
Like borrowed ideas from astraworld.com, human being factor or trivial and small visible vehicle driver once in a while exactly result fatal damage even vehicle have been equiped by various supply of safety.
Following tips which you Can pay attention before and when accelerate in roadway like borrowed ideas from by www.enjoythedrive.com.
# Avoid to calculate time. Draw up time which last for to target, without You have to in a hurry and race Your vehicle redundantly. Because drive in a hurry and panic might possibly result fatal You.
# Arrange position sit. Look for senyaman position possible. Because, if You drive in a state of is jumpy, conduct at situation and drive around even also can decrease.
# Avoid to put interesting goods in drive cabin, though that is very good decoration object. This matter to obviate You from no attention of moment drive.
# If needing, add Your rear view. With many rear view, eyesight up at back become more maximal. If needing, change also Your mirrors of the size larger ones. Arrange to aim to various angle corner. That way, You can watch car exist in back and or beside left right of Your car.
# Ascertaining goods like CD / map book cassette in a place it. CD/cassette, book, map, which is spilled (especially in facia) of fall if car press brake or quake. If it does, You'D busy with managing it and situation walke even also will be uncared.
# Remain to pay attention road street and labour in order not to change over view. By paying attention road street, You'D always allert if happened something in front of or beside Your vehicle right-left.
# Paying attention also other driver. Besides You, car around You even also can become its cause of accident. The root cause is sleepy.
Usually sleepy rider of ride moment have fast marking too near by rear other car, going about column and press brake without cause, and also quicken fastly of car later then slowing down it again not of course. If You deal with driver like this, can possible, avoid. (algooth.putranto@bisnis. co.id)
Algooth Putranto.
***
Source : Translated from Business Indonesia
Its meaning, every year of roadway can kill 300 times more than Flu Bird virus victim which only reaching 100 people more.
Victim Accident of roadway do not recognize age, gender till religion. In roadway, who is even also can become victim.
The accident influenced by various factor, like accretion of is amount of resident which disproportionately with amount of addition of joint streets, weak of straightening of and law applying of order related to vehicle security and usage in road street, and also still loosen road street consumer society discipline.
Like borrowed ideas from astraworld.com, human being factor or trivial and small visible vehicle driver once in a while exactly result fatal damage even vehicle have been equiped by various supply of safety.
Following tips which you Can pay attention before and when accelerate in roadway like borrowed ideas from by www.enjoythedrive.com.
# Avoid to calculate time. Draw up time which last for to target, without You have to in a hurry and race Your vehicle redundantly. Because drive in a hurry and panic might possibly result fatal You.
# Arrange position sit. Look for senyaman position possible. Because, if You drive in a state of is jumpy, conduct at situation and drive around even also can decrease.
# Avoid to put interesting goods in drive cabin, though that is very good decoration object. This matter to obviate You from no attention of moment drive.
# If needing, add Your rear view. With many rear view, eyesight up at back become more maximal. If needing, change also Your mirrors of the size larger ones. Arrange to aim to various angle corner. That way, You can watch car exist in back and or beside left right of Your car.
# Ascertaining goods like CD / map book cassette in a place it. CD/cassette, book, map, which is spilled (especially in facia) of fall if car press brake or quake. If it does, You'D busy with managing it and situation walke even also will be uncared.
# Remain to pay attention road street and labour in order not to change over view. By paying attention road street, You'D always allert if happened something in front of or beside Your vehicle right-left.
# Paying attention also other driver. Besides You, car around You even also can become its cause of accident. The root cause is sleepy.
Usually sleepy rider of ride moment have fast marking too near by rear other car, going about column and press brake without cause, and also quicken fastly of car later then slowing down it again not of course. If You deal with driver like this, can possible, avoid. (algooth.putranto@bisnis. co.id)
Algooth Putranto.
***
Source : Translated from Business Indonesia
Take Care of Fuel Filter, Cleaning or Change
Sudden Machine car moment of not run properly, don't be direct of panic. It is possible that that thing happened because fuel filter (filter fuel) dirty. If do not be done by treatment You'D continue gnaw at s.t. of is condition of machine like less energy, felt to weaken though gas pedal stepped on profusely.
If symptom early this let without handling, next occurence can more hard, from not run properly machine even walk out because fuel stream to machine pursued or desisted is at all.
Checking and changing fuel filter will much more light than improve repairing generated by damage if fuel filter do not work better. As filter, role of fuel filter to machine performance very big.
This component undertake to discontinue water and dirt which implied in fuel. Otherwise there is fuel filter, that pest material can continue to carve a way through to fuel system.
Ready made of public secret of quality of fuel in Indonesia do not clear of water and dirt. And water dirt at fuel can destroy fuel system component and cause corrosion.
If that thing happened combustion becoming not perfect because juicy pregnant fuel will cause gas emission throw away abysmal of friendly sill boundary of environment.
Content irrigate or dirt exist in fuel also can result damage (worn-out) at passed by component it. For example, rust in cylinder wall. If this worn-out happened, will trigger leakage at room burn.
See its duty, if this is component too dirty, gasoline entering to room burn annoyed clear so that machine performance follow to have problem. In consequence, cleaning periodical fuel filter is obligation.
Cleaning this fuel filter is ideally done by each every fold 5.000 km. Do also fuel filter replacement each every fold 10.000 km.
Replacement require to be done by routine remember elementary materials of fuel filter is paper owning pore to filter fuel.
Old too long the pore becoming meeting so that difficult fuel is at all penetrating it.
If have that way meeting, will do not want to have to change with new filter. Still, this theory only applying to substance machine burn gasoline.
Diesel engine.
At substance machine burn diesel fuel (our attention diesel) to fuel filter even only one, that is replacement each every fold 10.000. Can be quicker if there is machine power indication decrease.
Fuel diesel fuel filter or diesel engine cannot be cleaned. Its replacement much more quickly because diesel fuel fuel circulating in marketing have its particle content till 4.000-5.000 ppm. So that quicken diesel fuel fuel filter stuff up.
Filter diesel age can be longer if using diesel fuel fuel owning smooth particle content. justly Mention of obstetrical PertaDEX of maximum particle only 300 particles per million (ppm). This type of used compatible for the diesel engine of common-rail.
Machine this type of have wear by common of premium diesel car. From way of its activity of fuel given by high pressure pass pump (high pressured) which moved electronically.
that high pressured Fuel accomodated in cross-section pipe (rail) before channelled independently to each every nozzle, as according to machine rotation and combustion sequence in each every cylinder.
At common-rail diesel engine, pressure comparison 1:18, lower than ordinary diesel engine which range from 1:20 and 1:25.
Equally, machine this type of is softer.
Because its technology this rail common diesel engine ask diesel fuel with maximum particle content 500-1.000 ppm base on its producer. If diesel fuel this type of consumed by Your vehicle, just in act to to more and more diligent clean Your car filter fuel. (algooth.putranto@bisnis.co.id)
Algooth Putranto.
***
Source : Translated from Business Indonesia
If symptom early this let without handling, next occurence can more hard, from not run properly machine even walk out because fuel stream to machine pursued or desisted is at all.
Checking and changing fuel filter will much more light than improve repairing generated by damage if fuel filter do not work better. As filter, role of fuel filter to machine performance very big.
This component undertake to discontinue water and dirt which implied in fuel. Otherwise there is fuel filter, that pest material can continue to carve a way through to fuel system.
Ready made of public secret of quality of fuel in Indonesia do not clear of water and dirt. And water dirt at fuel can destroy fuel system component and cause corrosion.
If that thing happened combustion becoming not perfect because juicy pregnant fuel will cause gas emission throw away abysmal of friendly sill boundary of environment.
Content irrigate or dirt exist in fuel also can result damage (worn-out) at passed by component it. For example, rust in cylinder wall. If this worn-out happened, will trigger leakage at room burn.
See its duty, if this is component too dirty, gasoline entering to room burn annoyed clear so that machine performance follow to have problem. In consequence, cleaning periodical fuel filter is obligation.
Cleaning this fuel filter is ideally done by each every fold 5.000 km. Do also fuel filter replacement each every fold 10.000 km.
Replacement require to be done by routine remember elementary materials of fuel filter is paper owning pore to filter fuel.
Old too long the pore becoming meeting so that difficult fuel is at all penetrating it.
If have that way meeting, will do not want to have to change with new filter. Still, this theory only applying to substance machine burn gasoline.
Diesel engine.
At substance machine burn diesel fuel (our attention diesel) to fuel filter even only one, that is replacement each every fold 10.000. Can be quicker if there is machine power indication decrease.
Fuel diesel fuel filter or diesel engine cannot be cleaned. Its replacement much more quickly because diesel fuel fuel circulating in marketing have its particle content till 4.000-5.000 ppm. So that quicken diesel fuel fuel filter stuff up.
Filter diesel age can be longer if using diesel fuel fuel owning smooth particle content. justly Mention of obstetrical PertaDEX of maximum particle only 300 particles per million (ppm). This type of used compatible for the diesel engine of common-rail.
Machine this type of have wear by common of premium diesel car. From way of its activity of fuel given by high pressure pass pump (high pressured) which moved electronically.
that high pressured Fuel accomodated in cross-section pipe (rail) before channelled independently to each every nozzle, as according to machine rotation and combustion sequence in each every cylinder.
At common-rail diesel engine, pressure comparison 1:18, lower than ordinary diesel engine which range from 1:20 and 1:25.
Equally, machine this type of is softer.
Because its technology this rail common diesel engine ask diesel fuel with maximum particle content 500-1.000 ppm base on its producer. If diesel fuel this type of consumed by Your vehicle, just in act to to more and more diligent clean Your car filter fuel. (algooth.putranto@bisnis.co.id)
Algooth Putranto.
***
Source : Translated from Business Indonesia
Recognizing Electricity System of Car
Electricity system of car in a condition standard only supplied by accumulator yielding tension equal to 12 volt. Because is small, car consumer is obliged to recognize matter which is is one this.
Small even, car electrics have ability of cayenne basin. Because sprinkling it, car electrics can cause burning. Start from small fire of car cause walk out make machine really burnt.
To avoid that thing happened, cable installation have to be paid attention better when doing accessory replacement like cabin lamp till system sound.
Very good to paying attention good ground system. By paying attention this matter of mistake installation moment can minimize. Like moment happened short link of electrics current, electrics energi which cannot be channelled do not will heap too big.
Things required to paid attention if wishing new installation tide for example is to ascertain wrong cable installation nothing that. Paying attention every existing extension. Its dissociation have to perfect in order not to happened possibility of short link of electrics current.
Afterwards , don't there is open let extension, so that cable interior seen.
Cover wear insulation each time have done cable extension.
Interfacing to bodi Pay attention also part of cable which incircuit with ground. Ascertaining installation don't be which is just done by there no ground. If confusing to look for extension which is flange to ground, just connective of its cable with made car body from sheet metal.
If sure find cable which incircuit with ground, check at installation fuse.
Ascertaining fuse capacities as according to required electricity capacities.
Don't be smaller or bigger than requirement. If given by smaller fuse, fuse will often break. On the contrary, if bigger very dangerous and rentan happened short link.
If You less sure ably You is, whereas desire add new accessory have 'in crown' just better be be brought it to its expert or to workshop mechanic.
Count by delivering car to its expert, You can at the same time pay attention way they work so that soybean cake if at later then day there is problem, You can doing alone him. (algooth.putranto@bisnis.co.id)
***
Source : Translated from Business Indonesia
Small even, car electrics have ability of cayenne basin. Because sprinkling it, car electrics can cause burning. Start from small fire of car cause walk out make machine really burnt.
To avoid that thing happened, cable installation have to be paid attention better when doing accessory replacement like cabin lamp till system sound.
Very good to paying attention good ground system. By paying attention this matter of mistake installation moment can minimize. Like moment happened short link of electrics current, electrics energi which cannot be channelled do not will heap too big.
Things required to paid attention if wishing new installation tide for example is to ascertain wrong cable installation nothing that. Paying attention every existing extension. Its dissociation have to perfect in order not to happened possibility of short link of electrics current.
Afterwards , don't there is open let extension, so that cable interior seen.
Cover wear insulation each time have done cable extension.
Interfacing to bodi Pay attention also part of cable which incircuit with ground. Ascertaining installation don't be which is just done by there no ground. If confusing to look for extension which is flange to ground, just connective of its cable with made car body from sheet metal.
If sure find cable which incircuit with ground, check at installation fuse.
Ascertaining fuse capacities as according to required electricity capacities.
Don't be smaller or bigger than requirement. If given by smaller fuse, fuse will often break. On the contrary, if bigger very dangerous and rentan happened short link.
If You less sure ably You is, whereas desire add new accessory have 'in crown' just better be be brought it to its expert or to workshop mechanic.
Count by delivering car to its expert, You can at the same time pay attention way they work so that soybean cake if at later then day there is problem, You can doing alone him. (algooth.putranto@bisnis.co.id)
***
Source : Translated from Business Indonesia
Driving Pregnant Moment
Driving whilst Pregnant, why not. Activity which possible have become routinized to some of this womankind, admit of to be done although in a state of pregnancy. But, this activity shall be done with interest beware of. Driving at present day is not activity which can only be done by man clan. But how if the mother with a child, is it possible that activity drive which have become routinized stopped for the time being until the baby born and mother return strength to drive?
Its answer all kinds of. There is which agree that activity is discontinued the time being, there is also having a notion to drive to admit of to be done by pregnant mother. Any that, driving shall be done carefully, particularly to pregnant mother.
Before coming up with what earning or cannot be done by all mother to be in driving. Better comprehend beforehand that even pertained activity of high risk, pregnant mother remain to earn to drive safely and is balmy. All obstetrical expert of pregnant woman agreement admit of to drive freely till obstetrical age seven months. This because stout size measure it stomach still small relative. Moreover foetus position still mobile. Admit of to make a move rather free in bag of water which also have the character of to weaken vibration.
Shock Silencer.
First matter which must be remembered by select choose balmiest vehicle. Vehicle freshment supported by adopted by suspension system is used vehicle. Good suspension for taking a short cut natural by vibration of spiral spring. Car type rode by pregnant woman better which is soft suspension. soft suspension system guarantee natural by vibration the the mother do not too hard and quickly lose. Shock Car have an effect on to tired storey level of mother.
“suspension system using spring helical, such as those which adopted many by sedan, small car, van, and some of newest output minibus more compatible to pregnant mother. just Only is of minibus cabin generally rather high, so that enough difficult to taking a ride her.” say Cakra Wiyata, Business Development ZF Trading Indonesia, Shock silencer producer and Sachs clutch,
Tuesday (19 / 10).
Cakra Enhance, better avoid car like jip (more than anything else which is offroad). Jip usually use leaf spiral spring (spring leaf), hard and stiffer compared to spring helical. Any of vehicle suspension system, avoid road street route which is holes or bad once.
Seat position have to be balmy. Its way, backing into seat to give bigger room, and back into seat around 30 degree of rear.
Becoming, drive do not hit hand and stomach is not difficult hold drive. Require to be paid attention foot/feet position, may not hang fixed can reach gas pedal, rem and clutch.
When wishing balmier without fearing drive jog stomach, can use small pillow among stomach driven. election of Belt peacemaker also determine to freshment. Select Choose peacemaker belt with three dot able to be accomodated, that is peacemaker belt able to follow body motion (elastic), but moment happened collision can hitch to backside.(tot)
***
Source : Translated from sinarharapan.co.id
Its answer all kinds of. There is which agree that activity is discontinued the time being, there is also having a notion to drive to admit of to be done by pregnant mother. Any that, driving shall be done carefully, particularly to pregnant mother.
Before coming up with what earning or cannot be done by all mother to be in driving. Better comprehend beforehand that even pertained activity of high risk, pregnant mother remain to earn to drive safely and is balmy. All obstetrical expert of pregnant woman agreement admit of to drive freely till obstetrical age seven months. This because stout size measure it stomach still small relative. Moreover foetus position still mobile. Admit of to make a move rather free in bag of water which also have the character of to weaken vibration.
Shock Silencer.
First matter which must be remembered by select choose balmiest vehicle. Vehicle freshment supported by adopted by suspension system is used vehicle. Good suspension for taking a short cut natural by vibration of spiral spring. Car type rode by pregnant woman better which is soft suspension. soft suspension system guarantee natural by vibration the the mother do not too hard and quickly lose. Shock Car have an effect on to tired storey level of mother.
“suspension system using spring helical, such as those which adopted many by sedan, small car, van, and some of newest output minibus more compatible to pregnant mother. just Only is of minibus cabin generally rather high, so that enough difficult to taking a ride her.” say Cakra Wiyata, Business Development ZF Trading Indonesia, Shock silencer producer and Sachs clutch,
Tuesday (19 / 10).
Cakra Enhance, better avoid car like jip (more than anything else which is offroad). Jip usually use leaf spiral spring (spring leaf), hard and stiffer compared to spring helical. Any of vehicle suspension system, avoid road street route which is holes or bad once.
Seat position have to be balmy. Its way, backing into seat to give bigger room, and back into seat around 30 degree of rear.
Becoming, drive do not hit hand and stomach is not difficult hold drive. Require to be paid attention foot/feet position, may not hang fixed can reach gas pedal, rem and clutch.
When wishing balmier without fearing drive jog stomach, can use small pillow among stomach driven. election of Belt peacemaker also determine to freshment. Select Choose peacemaker belt with three dot able to be accomodated, that is peacemaker belt able to follow body motion (elastic), but moment happened collision can hitch to backside.(tot)
***
Source : Translated from sinarharapan.co.id
Water Accumulator Car Quickly Finished
1. Immediately check accumulator body what is there is barst? Barst at accumulator bodi result accumulator water seep exit slowly. Other characteristic is accumulator tatakan usually contamination with white dust, like corrosion at accumulator head.
2. Overcharging (excess of payload), natural accumulator of excess of current payload will experience of warm-up. Accumulator water of expand and condense so that will quickly decrease.
Tune to repeat accumulator filling band. Change IC regulator because big possibility destroy. Check alternator size measure with accumulator capacities whether is proportional.
Accumulator 45 ampere will quickly finished its water if given by alternator 90 ampere. Because overcharging.
***
Source : Translated from duniabengkel.com
2. Overcharging (excess of payload), natural accumulator of excess of current payload will experience of warm-up. Accumulator water of expand and condense so that will quickly decrease.
Tune to repeat accumulator filling band. Change IC regulator because big possibility destroy. Check alternator size measure with accumulator capacities whether is proportional.
Accumulator 45 ampere will quickly finished its water if given by alternator 90 ampere. Because overcharging.
***
Source : Translated from duniabengkel.com
Muffler like fire a gun
But it is true Muffler can explode because of existence of the rest of gas throw away which not yet burnt in room burn and burnt in Muffler. Hence bursting the remains fuel in Muffler is so that heard by its eruption of this eruption happened at the (time) of you discharge gas pedal.
To avoid happened eruption like this it is better you do tune-up with important point inform to mechanic that you hear eruption. Good mechanic surely will do carburetor around tune-up and ignition system.
Arrangement at carburettor needed to fuel mixture and perfect air, though do not one hundred perfect % but surely will lessen the happening of external combustion. Considering vehicle age and its component.
Arrangement at ignition system cover tuning of timing (by turning around distributor assisted by means of ... timing-light) searching correct timing as according to machine specification. Do not forget also pay attention the condition of spark plug and tune gap (gap) be snugly.
Sometimes tuning of valve is also needed in this problem. Cause here gasoline fuel entrance.
Don't be hard wrong of this picture… make you which is this know of its name of thrower flame, there is special appliance which transplanted by at attributed to Muffler example system is switch, by exploiting the rest of gas throw away.. but there are some kit which peculiarly enhance gasoline so that yielded fire can be longer and more “Scrub”
***
Source : Translated from duniabengkel.com
To avoid happened eruption like this it is better you do tune-up with important point inform to mechanic that you hear eruption. Good mechanic surely will do carburetor around tune-up and ignition system.
Arrangement at carburettor needed to fuel mixture and perfect air, though do not one hundred perfect % but surely will lessen the happening of external combustion. Considering vehicle age and its component.
Arrangement at ignition system cover tuning of timing (by turning around distributor assisted by means of ... timing-light) searching correct timing as according to machine specification. Do not forget also pay attention the condition of spark plug and tune gap (gap) be snugly.
Sometimes tuning of valve is also needed in this problem. Cause here gasoline fuel entrance.
Don't be hard wrong of this picture… make you which is this know of its name of thrower flame, there is special appliance which transplanted by at attributed to Muffler example system is switch, by exploiting the rest of gas throw away.. but there are some kit which peculiarly enhance gasoline so that yielded fire can be longer and more “Scrub”
***
Source : Translated from duniabengkel.com
Brake Disc
Rem System which is one this most simple and very reliable used as vehicle stopping, system put on the brakes this usually located in next position of your vehicle.
This System component is.
1. Pads Brake (rem canvas)
2. Caliper (in caliper there are rem piston)
3. Disc rotor (saucer in form of is domed)
Way of this system activity at the (time) of fast you and depress pedal put on the brakes hence :
1. Rem oil which is exerting pressure push piston go out from home caliper
2. Piston put on the brakes later then push canvas put on the brakes toward rotatory rotor
3. Friction between rotor and canvas make vehicle desist.
4. Earn you conceive rem canvas job/activity arrest detain vehicle burden..??
5. At caliper there are 2 seal, piston seal and dirt seal preventing dirt enter and erode external surface of piston.
6. Later Then rotor will depress again canvas put on the brakes after your rem pedal release.
***
Source : Translated from duniabengkel.com
This System component is.
1. Pads Brake (rem canvas)
2. Caliper (in caliper there are rem piston)
3. Disc rotor (saucer in form of is domed)
Way of this system activity at the (time) of fast you and depress pedal put on the brakes hence :
1. Rem oil which is exerting pressure push piston go out from home caliper
2. Piston put on the brakes later then push canvas put on the brakes toward rotatory rotor
3. Friction between rotor and canvas make vehicle desist.
4. Earn you conceive rem canvas job/activity arrest detain vehicle burden..??
5. At caliper there are 2 seal, piston seal and dirt seal preventing dirt enter and erode external surface of piston.
6. Later Then rotor will depress again canvas put on the brakes after your rem pedal release.
***
Source : Translated from duniabengkel.com
Drum Brake
Rem behind your vehicle generally have brake drum type, although it is true by dozens which have changed to become brake
disc. Brake drum have grip energy which do not fail with brake disc, evidence if will try to pay attention big truck,
type put on the brakes what used, surely its answer is brake drum.
Drum brake component among others :
1. Cylinder Brake
2. Piston
3. Mechanism put on the brakes hand
4. Cable put on the brakes hand
5. Shoes Brake (brake lining)
6. Regulator brake lining mechanism
7. Drum
8. Spiral spring / Per.
Way of brake drum activity at the (time) of accelerate you depress pedal put on the brakes hence :
1. Rem master push oil put on the brakes which have compressible toward cylinder brake
2. Piston which there are in cylinder brake depress brake lining up at drum which is rotating
3. Spiral spring found on regulator mechanism follow length correspond to pressure given by piston.
4. After you discharge pedal put on the brakes hence pressure change rotatory brake drum will again push brake lining
5. And spiral spring will draw brake lining on course initially
6. Piston put on the brakes also will return to position initially
But brake drum type also have weakness, one of them is if across water pond, suffused water can enter into drum and paralyse
rem system, but only is tentative, tips for the you of is “after passing water pond, depress and hold up pedal put on the
brakes for a few moment”, and ascertain brake drum have nipped again.
***
Source : Translated from duniabengkel.com
disc. Brake drum have grip energy which do not fail with brake disc, evidence if will try to pay attention big truck,
type put on the brakes what used, surely its answer is brake drum.
Drum brake component among others :
1. Cylinder Brake
2. Piston
3. Mechanism put on the brakes hand
4. Cable put on the brakes hand
5. Shoes Brake (brake lining)
6. Regulator brake lining mechanism
7. Drum
8. Spiral spring / Per.
Way of brake drum activity at the (time) of accelerate you depress pedal put on the brakes hence :
1. Rem master push oil put on the brakes which have compressible toward cylinder brake
2. Piston which there are in cylinder brake depress brake lining up at drum which is rotating
3. Spiral spring found on regulator mechanism follow length correspond to pressure given by piston.
4. After you discharge pedal put on the brakes hence pressure change rotatory brake drum will again push brake lining
5. And spiral spring will draw brake lining on course initially
6. Piston put on the brakes also will return to position initially
But brake drum type also have weakness, one of them is if across water pond, suffused water can enter into drum and paralyse
rem system, but only is tentative, tips for the you of is “after passing water pond, depress and hold up pedal put on the
brakes for a few moment”, and ascertain brake drum have nipped again.
***
Source : Translated from duniabengkel.com
Damage of Rem
SEARCHING SYMPTOM DAMAGE of REM.
At the (time) of you ride vehicle from time to time, you surely have felt difference which you experience of, sometime pedal put on the brakes felt is bizzare, is sometime heard by voice cheep, or possible other occurence which make surprise... So now we will study what you can detect from mentioned rem symptom..
First of all we have to know first how to work rem, rem work with changing style fiddle to discontinue fastly of vehicle. At the (time) of you depress rem pedal, rem oil will empty into pipe put on the brakes and depress piston and distribute to rem canvas, later then have friction to with disk or canister and discontinue fastly of its rotation. Boisterous progressively passed to pressure is rem pedal gain strength also given pressure to disk or canister and faster also vehicle desist. So now you have known how rem work.
After you know the way of activity put on the brakes now we study first problem, what is going on if natural rem system of leakage. If natural rem system of leakage hence air will enter into rem system, and rem pedal will felt “pack”. Is such as those which told by “Bernouli” that dilution can continue pressure without loss of force (power) little. So if your rem system experience of leakage hence rem pedal pressure do not aka matching with the one which you give caused by air in it. So also if your rem canvas start to attenuate hence respon to desist will longer, because distance (gap) between canvas with disk or canister.
Now we will study heard voices at the (time) of you ride vehicle :
1. very hard Friction voice (grinding / scratching)
This means you in big problem.. usually voice this happened because canvas put on the brakes have finished, and heard by voice is friction voice between canvas iron put on the brakes with canister or with disk.
Damage effect of this friction have irreparable and you need to fumble kocek which in to redeem a set canvas put on the brakes and canister or with disk.
To avoiding it, check periodical rem, change canvas put on the brakes if its thickness minimize 1mm for the canvas of put on the brakes behind canister, and 3mm for the canvas of next rem of disk.
2. Rem felt attactive to left or to right (pulls brake)
This means there is leakage at one of the rem kaliper, to know such like this its way, if rem felt attactive up at right mean leakage happened at its opponent that is on the left, because kaliper left side unable to give pressure which is equal to right (this can be interpreted happened leakage on the left) so also on the contrary.
You have known symptom which is often experienced by rem system, ascertaining consultancy you with professional mechanic before you try doing alone it, because mistake at rem system can cause very fatal accident even death.
***
Source : Translated from duniabengkel.com
At the (time) of you ride vehicle from time to time, you surely have felt difference which you experience of, sometime pedal put on the brakes felt is bizzare, is sometime heard by voice cheep, or possible other occurence which make surprise... So now we will study what you can detect from mentioned rem symptom..
First of all we have to know first how to work rem, rem work with changing style fiddle to discontinue fastly of vehicle. At the (time) of you depress rem pedal, rem oil will empty into pipe put on the brakes and depress piston and distribute to rem canvas, later then have friction to with disk or canister and discontinue fastly of its rotation. Boisterous progressively passed to pressure is rem pedal gain strength also given pressure to disk or canister and faster also vehicle desist. So now you have known how rem work.
After you know the way of activity put on the brakes now we study first problem, what is going on if natural rem system of leakage. If natural rem system of leakage hence air will enter into rem system, and rem pedal will felt “pack”. Is such as those which told by “Bernouli” that dilution can continue pressure without loss of force (power) little. So if your rem system experience of leakage hence rem pedal pressure do not aka matching with the one which you give caused by air in it. So also if your rem canvas start to attenuate hence respon to desist will longer, because distance (gap) between canvas with disk or canister.
Now we will study heard voices at the (time) of you ride vehicle :
1. very hard Friction voice (grinding / scratching)
This means you in big problem.. usually voice this happened because canvas put on the brakes have finished, and heard by voice is friction voice between canvas iron put on the brakes with canister or with disk.
Damage effect of this friction have irreparable and you need to fumble kocek which in to redeem a set canvas put on the brakes and canister or with disk.
To avoiding it, check periodical rem, change canvas put on the brakes if its thickness minimize 1mm for the canvas of put on the brakes behind canister, and 3mm for the canvas of next rem of disk.
2. Rem felt attactive to left or to right (pulls brake)
This means there is leakage at one of the rem kaliper, to know such like this its way, if rem felt attactive up at right mean leakage happened at its opponent that is on the left, because kaliper left side unable to give pressure which is equal to right (this can be interpreted happened leakage on the left) so also on the contrary.
You have known symptom which is often experienced by rem system, ascertaining consultancy you with professional mechanic before you try doing alone it, because mistake at rem system can cause very fatal accident even death.
***
Source : Translated from duniabengkel.com
About Rem Car
ATTENTION.
Rem is especial component of vehicle, service shall only be done by one who is its area case hardened, mistake do service, causing accident even death.
1. Cleanse system put on the brakes each every 20.000km or at least 2 year once.
2. Paying attention rem oil colour, oil colour put on the brakes usually there is 2 that is transparent and squeeze, if have dirty or turn colour to cleanse and change with newly.
3. Check after small barst rem at the (time) of doing car tire giration, at the same time check the condition of rem canvas (cleaning when needed)
4. To all matic car consumer, accustoming at the (time) of stopping for to neutralize transmission to lessen burden put on the brakes as well as canvas transmission.
5. Consumer put on the brakes tromol (brake drum) have to take a care used up pass floods area, ascertaining rem have normal return by depressing pedal put on the brakes during a few moments.
6. Assist performance put on the brakes by doing brake engine (by using low tooth at the (time) of downhill road street)
7. Change canvas put on the brakes with qualified product.
***
Source : Translated from duniabengkel.com
Rem is especial component of vehicle, service shall only be done by one who is its area case hardened, mistake do service, causing accident even death.
1. Cleanse system put on the brakes each every 20.000km or at least 2 year once.
2. Paying attention rem oil colour, oil colour put on the brakes usually there is 2 that is transparent and squeeze, if have dirty or turn colour to cleanse and change with newly.
3. Check after small barst rem at the (time) of doing car tire giration, at the same time check the condition of rem canvas (cleaning when needed)
4. To all matic car consumer, accustoming at the (time) of stopping for to neutralize transmission to lessen burden put on the brakes as well as canvas transmission.
5. Consumer put on the brakes tromol (brake drum) have to take a care used up pass floods area, ascertaining rem have normal return by depressing pedal put on the brakes during a few moments.
6. Assist performance put on the brakes by doing brake engine (by using low tooth at the (time) of downhill road street)
7. Change canvas put on the brakes with qualified product.
***
Source : Translated from duniabengkel.com
Loose Rem, Don'T Panic
1. Immediately perceive the condition of around
2. Removing attention to fast stopping component of vehicle
3. Hand rem can be used
4. Brake Engine from high gear to low gear
5. Kill vehicle machine
6. Sounding horn to give signal at other driver
Step above including emergency step.
Your membership in ride very is determining of safety.
Valid for every vehicle type with manual transmission and automatically.
***
Source : Translated from duniabengkel.com
2. Removing attention to fast stopping component of vehicle
3. Hand rem can be used
4. Brake Engine from high gear to low gear
5. Kill vehicle machine
6. Sounding horn to give signal at other driver
Step above including emergency step.
Your membership in ride very is determining of safety.
Valid for every vehicle type with manual transmission and automatically.
***
Source : Translated from duniabengkel.com
Clean Car
1. Park calm car in place. Do not be hit by direct sunshine
2. Cleaning car interior interior with small comb, comb surface of seat, klo there is nicer cleaner vacum again, throw away existing dirt in vehicle.
3. Car douche with water until all its of wet, douche also part of like gallery of mine spatbord dirt lose.
4. Use special car shampoo which sold by many marketing, car shampoo have ability for the mengihilangkan of stain pock, and oil fleck, dissolving as according to suggested measuring.
5. Use sponge to clean car with shampoo, clean car with shampoo until entire/all clean surface.
6. Use wing soap and comb to clean tire, immediately rinse with water, after cleaning tire, soap wing enough ossify, if your vehicle velg of chrome enough use just car shampoo
7. After all surface of clean body cleaned with car shampoo, rinse until cleanness, ascertaining there no rest of shampoo which still stick car.
8. Use mop “chamois” to dry the rest of water.
9. Glass mop run dry
10. bone dry Body car mop until.
11. Using tire polish tire gleam
12. Using special polish to part of interior.
***
Source : Translated from duniabengkel.com
2. Cleaning car interior interior with small comb, comb surface of seat, klo there is nicer cleaner vacum again, throw away existing dirt in vehicle.
3. Car douche with water until all its of wet, douche also part of like gallery of mine spatbord dirt lose.
4. Use special car shampoo which sold by many marketing, car shampoo have ability for the mengihilangkan of stain pock, and oil fleck, dissolving as according to suggested measuring.
5. Use sponge to clean car with shampoo, clean car with shampoo until entire/all clean surface.
6. Use wing soap and comb to clean tire, immediately rinse with water, after cleaning tire, soap wing enough ossify, if your vehicle velg of chrome enough use just car shampoo
7. After all surface of clean body cleaned with car shampoo, rinse until cleanness, ascertaining there no rest of shampoo which still stick car.
8. Use mop “chamois” to dry the rest of water.
9. Glass mop run dry
10. bone dry Body car mop until.
11. Using tire polish tire gleam
12. Using special polish to part of interior.
***
Source : Translated from duniabengkel.com
Tips Buy Sokbreker
1. Paying attention sokbreker body, new material have to smoothly there is not weld econdhand, its paint nicely and is thick , like factory paint, is not paint.
2. Paying attention kode/stamp at sokbreker body, at sokbreker body there are brand which is usually carved with laser, or use special appliance to make their brand graven at sokbreker body.
3. Sticker which patch at its situation sokbreker body of perfection, because done by machine. There is not which is right or askew left. Sticker colour also see nicely because diprint by means of ... which with quality.
4. lustrous Ace sokbreker bar, there no an weld secondhand which is colored a few is rather blue, there is no secondhand incised, klo there is incision mean have have is used of ex- alias, because peripatetic sokbreker ace bar go up and alight from sokbreker body.
5. Wire thread at smooth and good sokbreker bar, is not harsh.
6. Paying attention undercarriage sokbreker anting, this easiest shares checked, whether/ what still smoothly or no, usually secondhand sokbreker anting is not circular.
7. Last newly Type test GAS for depress full sokbreker downwards and see do sokbreker return to position to the by itself (have to return). Paying attention its movement at the (time) of returning to position early (smoothly lancer do not be broken).
8. For the Type of OIL, depress downwards and draw again, giving attention to interesting moment of movement have to fast do not be broken by wind.
***
Source : Translated from duniabengkel.com
2. Paying attention kode/stamp at sokbreker body, at sokbreker body there are brand which is usually carved with laser, or use special appliance to make their brand graven at sokbreker body.
3. Sticker which patch at its situation sokbreker body of perfection, because done by machine. There is not which is right or askew left. Sticker colour also see nicely because diprint by means of ... which with quality.
4. lustrous Ace sokbreker bar, there no an weld secondhand which is colored a few is rather blue, there is no secondhand incised, klo there is incision mean have have is used of ex- alias, because peripatetic sokbreker ace bar go up and alight from sokbreker body.
5. Wire thread at smooth and good sokbreker bar, is not harsh.
6. Paying attention undercarriage sokbreker anting, this easiest shares checked, whether/ what still smoothly or no, usually secondhand sokbreker anting is not circular.
7. Last newly Type test GAS for depress full sokbreker downwards and see do sokbreker return to position to the by itself (have to return). Paying attention its movement at the (time) of returning to position early (smoothly lancer do not be broken).
8. For the Type of OIL, depress downwards and draw again, giving attention to interesting moment of movement have to fast do not be broken by wind.
***
Source : Translated from duniabengkel.com
Function, and treatment of Rear View Car
Following us give tips in around rear view :
1. Bend rear view if you feel environment around not peaceful, not peaceful from vehicle around as well as not peaceful from thief.
2. seen object at rear view always see nearer than its original object, because of usage of glass “convex” to add your safety factor function in ride.
3. Use rear view to know environment around when you'd alight from your vehicle.
4. Paying attention rear view angle corner position and situation to facilitate you watch your vehicle and around you.
5. For the things wearing electrical spion lubricate part of motorize protected from rust.
***
Source : Translated from duniabengkel.com
1. Bend rear view if you feel environment around not peaceful, not peaceful from vehicle around as well as not peaceful from thief.
2. seen object at rear view always see nearer than its original object, because of usage of glass “convex” to add your safety factor function in ride.
3. Use rear view to know environment around when you'd alight from your vehicle.
4. Paying attention rear view angle corner position and situation to facilitate you watch your vehicle and around you.
5. For the things wearing electrical spion lubricate part of motorize protected from rust.
***
Source : Translated from duniabengkel.com
Take Care Of Glass Film Car
Take the air week day, to major car market. Its plan will install car film glass, enunciated still date of is young there is fair to middling surplus funds of car film glass install let to add to associate with and most importantly can decrease hot of in car.
Make to take care of car film glass there its hold back by sunshine, like this its way :
1. Don'T degrade glass during 2 day, this is meant bone dry film to glass glue stick at glass.
2. Finished clean bone dry glass mop car until, labouring to clean car do not below/under sun, to avoid pock at glass.
3. Use special cleaner dilution for existing glass is marketing
4. Don'T film glass mop have with wet mop below/under sun. Different temperature at glass on the spur of the moment can destroy film glaze, film glass glue also can abrad because difference of temperature on the spur of the moment.
5. Avoid to open dusty area glass, dirt can cause film glaze incised.
6. Take care of periodical window pane rubber each every one month once by using ex-toothbrush, and shampoo clean until cleanness. Last spray silicon dilution (nub with cream pake polish tire) so that glass rubber growing durabelly.
***
Source : Translated from duniabengkel.com
Make to take care of car film glass there its hold back by sunshine, like this its way :
1. Don'T degrade glass during 2 day, this is meant bone dry film to glass glue stick at glass.
2. Finished clean bone dry glass mop car until, labouring to clean car do not below/under sun, to avoid pock at glass.
3. Use special cleaner dilution for existing glass is marketing
4. Don'T film glass mop have with wet mop below/under sun. Different temperature at glass on the spur of the moment can destroy film glaze, film glass glue also can abrad because difference of temperature on the spur of the moment.
5. Avoid to open dusty area glass, dirt can cause film glaze incised.
6. Take care of periodical window pane rubber each every one month once by using ex-toothbrush, and shampoo clean until cleanness. Last spray silicon dilution (nub with cream pake polish tire) so that glass rubber growing durabelly.
***
Source : Translated from duniabengkel.com
Drive Car Matic
Make mother circle usually most like go up car have automatic transmission, easy, remain press gas put on the brakes word one of the housewife which we have time to interview.
Real correct but as easy as that..? easy it is true, following us give information in around riding car which have automatic transmission.
1. car have automatic Transmission have to peacemaker at the (time) of will in starter, for that try to ascertain the the peacemaker function among others, transmission lever reside in on course Parking “P”. If Lever transmission do not reside in on course “P” ascertained by car you will not live to let starter thousand times.
2. So, if you will take the air to mother market don't forget if will starter machine, ascertaining handbrake (hand rem) still on course lock, later then this machin, starter is guaranteed can live, but there is also vehicle using foot/feet rem as peacemaker for the starter of car, for that you have to depress pedal put on the brakes machine earn starter. Like BMW and Mercy you have to depress pedal put on the brakes machine earn starter.
3. Already life machine, now depress pedal put on the brakes and remove lever to Drive position “D”, free slow rem and let to accelerate slowly with gas pedal addition.
4. At the (time) of desisting red light it is better you remove neutral transmission lever On course “N” so that machine burden decrease because arrested by rem, activity put on the brakes also become light because do not arrest detain machine burden, transmission age can be longer because do not be forced to arrest detain burden.
5. Make which accustomed ride car with manual transmission, require to take heed left foot/feet movement.. recognize pedal formation there's only gas and rem. Have there is this humorous occurence happened at myself.. become will lose face because accustomed to pedal clutch, time wished to desist off the cuffly I step on pedal put on the brakes by 2 long rem pedal although foot/feet fruit, my small foot/feet become use tread 2 foot/feet at the same time is, cash of friend beside me as long as to office journey.. elementary.. (usage of pedal put on the brakes and real correct gas by using 1 just foot/feet that is right foot/feet)
6. Take the air to go up mount, bring beloved family go up matic car, walked by jam, calm… use low gear (don't be wrong let matic there is gear one him also) this matter is meant to be transmission do not “overload”. Overload cut short clutch canvas age.
7. Go home from going up mount now go down mount.. still stuck is also walked, enunciated everybody at returning from vacation.. is same as at point above using low gear, this but meant rem to canvas do not too heavy, matic most extravagant rem canvas, this one of the way of to economize rem canvas.
8. Already free from to stuck now step into turnpike, remain lever move to Drive position “D”, cosiest if there is “control cruise” gas panting in number 80km/cruise knob press hour ‘ceklik’ direct already car of road street alone ga take care gas press again. (control cruise function will lose so you depress rem pedal)
9. To at home its problem happiness is walked meekly traffic fringe, belt peacemaker not of take care to be studied by law again.. already is obliged to its.. park house garage, returning lever on course Park “P”, interesting of hand rem and kill machine.
***
Source : Translated from duniabengkel.com
Real correct but as easy as that..? easy it is true, following us give information in around riding car which have automatic transmission.
1. car have automatic Transmission have to peacemaker at the (time) of will in starter, for that try to ascertain the the peacemaker function among others, transmission lever reside in on course Parking “P”. If Lever transmission do not reside in on course “P” ascertained by car you will not live to let starter thousand times.
2. So, if you will take the air to mother market don't forget if will starter machine, ascertaining handbrake (hand rem) still on course lock, later then this machin, starter is guaranteed can live, but there is also vehicle using foot/feet rem as peacemaker for the starter of car, for that you have to depress pedal put on the brakes machine earn starter. Like BMW and Mercy you have to depress pedal put on the brakes machine earn starter.
3. Already life machine, now depress pedal put on the brakes and remove lever to Drive position “D”, free slow rem and let to accelerate slowly with gas pedal addition.
4. At the (time) of desisting red light it is better you remove neutral transmission lever On course “N” so that machine burden decrease because arrested by rem, activity put on the brakes also become light because do not arrest detain machine burden, transmission age can be longer because do not be forced to arrest detain burden.
5. Make which accustomed ride car with manual transmission, require to take heed left foot/feet movement.. recognize pedal formation there's only gas and rem. Have there is this humorous occurence happened at myself.. become will lose face because accustomed to pedal clutch, time wished to desist off the cuffly I step on pedal put on the brakes by 2 long rem pedal although foot/feet fruit, my small foot/feet become use tread 2 foot/feet at the same time is, cash of friend beside me as long as to office journey.. elementary.. (usage of pedal put on the brakes and real correct gas by using 1 just foot/feet that is right foot/feet)
6. Take the air to go up mount, bring beloved family go up matic car, walked by jam, calm… use low gear (don't be wrong let matic there is gear one him also) this matter is meant to be transmission do not “overload”. Overload cut short clutch canvas age.
7. Go home from going up mount now go down mount.. still stuck is also walked, enunciated everybody at returning from vacation.. is same as at point above using low gear, this but meant rem to canvas do not too heavy, matic most extravagant rem canvas, this one of the way of to economize rem canvas.
8. Already free from to stuck now step into turnpike, remain lever move to Drive position “D”, cosiest if there is “control cruise” gas panting in number 80km/cruise knob press hour ‘ceklik’ direct already car of road street alone ga take care gas press again. (control cruise function will lose so you depress rem pedal)
9. To at home its problem happiness is walked meekly traffic fringe, belt peacemaker not of take care to be studied by law again.. already is obliged to its.. park house garage, returning lever on course Park “P”, interesting of hand rem and kill machine.
***
Source : Translated from duniabengkel.com
Car Chok Up Because Dirty Gasoline
Your Car machine stagnation?
Try to check component in your machine following :
1. After gasoline
2. Gasoline Filter
3. Carburettor
Usually 3 factor above becoming stagnation car source, will press gas also die.
Check water and dirt at 3 component above guaranteed good..
***
Source : Translated from duniabengkel.com
Try to check component in your machine following :
1. After gasoline
2. Gasoline Filter
3. Carburettor
Usually 3 factor above becoming stagnation car source, will press gas also die.
Check water and dirt at 3 component above guaranteed good..
***
Source : Translated from duniabengkel.com
Cheque Condition Of Cover Distributor Chop
Many name make machine component which is one this. Era first era mechanic “belande” mostly spell out members Navoor make this fire divisor component.
Its tabletop in form of like cuttle hand, because spark plug cable place patch. Amount of cable as according to your car machine cylinder content.
Generally at conventional machine usually for the machine of 4 cylinder there is 5 cable, for the machine of 6 cylinder there is 7 cable and for the machine of 8 cylinder there is 9 cable.
Detect damage which often happened at distributor possible you have experiencing of it.
1. Weak Car attraction caused by the happening of leakage of electrics current caused by cart at distributor cover, so that sprinkling of exit fire look for mass (ground)
2. storing at car audio, electrics current which is leaky to be arrested by unit head signal because very sensitive with electrics current ”timeworn”
***
Source : Translated from duniabengkel.com
Its tabletop in form of like cuttle hand, because spark plug cable place patch. Amount of cable as according to your car machine cylinder content.
Generally at conventional machine usually for the machine of 4 cylinder there is 5 cable, for the machine of 6 cylinder there is 7 cable and for the machine of 8 cylinder there is 9 cable.
Detect damage which often happened at distributor possible you have experiencing of it.
1. Weak Car attraction caused by the happening of leakage of electrics current caused by cart at distributor cover, so that sprinkling of exit fire look for mass (ground)
2. storing at car audio, electrics current which is leaky to be arrested by unit head signal because very sensitive with electrics current ”timeworn”
***
Source : Translated from duniabengkel.com
The Rains and car
The rains will immediately come, estimate from BMG “Badan Meteorologi dan Geofisika” Indonesia estimate that in the year 2008
is the rains will take place sufficiently long.
As well as there will be some estimated metropolis also danger rentan of floods. For that we are duniabengkel team feel
important to give article about is important preparation of your vehicle to face the rains.
There are special preparation make your vehicle and you during the rains. This of duniabengkel team will give complete
envelope to be balmy and peaceful during the rains ride, for that follow tips from us following :
1. Slippery and Wet Public road will become your everyday food is the rains, for that vehicle you have to have TIRE with good
yan path.
Tire with correct path will prevent the happening of symptom “aquaplanning” (loss of tire traction to asphalt).
Not merely just tire path which paid attention but also mount wear of tire, mount keausan of high tire will very dangerous.
Condition of slippery road street can result vehicle losing of traction and can result accident even death.
Following inspection tips at your vehicle tire :
* Tire path have to goodness, minimum is condition of tire 65%.
* Check tire wind pressure arrange according to manufacturer guide.
* Tire character have to as according to condition of road street, tire with specification of terrain mud (MT) very do not
recommend for the the rains of use tire with minimum specification of All Terrain (AT)
* If (there are) any surplus funds usage of special tire like wet tire will be more be peaceful. But tire manufacturer
technology now claim that their peaceful tire to be used at 2 season in Indonesia.
2. your Machine Vehicle need electrics entered to be can operate. Era now more than anything else.. already technology go
forward already.. cars arranged is same which is its name of ECU (module control elktronik).
But technological excess non meaning without insuffiency. You surely understand correctness that electricity component very
same susceptible which its name of water, like that with car, water can become riskiest cause at electricity system, can
result konslet.
Nature of water which is conductor earn konslet make vehicle key parts like ECU, Alternator etc. If have destroyed must case
most of these, changed by because is irreparable, price which is must redeemed costly fair to middling also.
For that before facing the rains you need to pay attention electricity system of your vehicle, especially part of following :
1. ECU, its costly price, don't to damage
2. CDI, way of its activity loo like ECU, its costly price also, don't to damage
3. Alternator, the heart of electricity system, costly fair to middling also its price
4. Coil, the heart of ignition system
5. Cable Spark plug and Spark plug, don'to wet
6. Accu / battery
7. Distributor
8. Irrigate Filter (air filter) can make hammer water (water enter into machine)
9. Carburettor
10. Injector
11. platinum
3. Go up car still rain… decrease to be decreased in the reality there is leaky, in the reality which become its ringleader
of door cover rubber which is already fragible. For that give attention of extra to the item rubber, change when needed, not
costly. Usually 1 priced door Rp 30-40.000
4. Cheque repeat the condition of wiper motor, wiper rubber and next glass of vehicle.
5. Check cooling system (AC) when rain. Interior can mist if AC not life, view to the fore become to turn tail.
6. Check elegibility of fog light (light fog)
So already at cheque repeat altogether, don't forget to play the game traffic keep distance peacefully of ride, and don't
forget to impose peacemaker belt.
***
Source : Translated from duniabengkel.com
is the rains will take place sufficiently long.
As well as there will be some estimated metropolis also danger rentan of floods. For that we are duniabengkel team feel
important to give article about is important preparation of your vehicle to face the rains.
There are special preparation make your vehicle and you during the rains. This of duniabengkel team will give complete
envelope to be balmy and peaceful during the rains ride, for that follow tips from us following :
1. Slippery and Wet Public road will become your everyday food is the rains, for that vehicle you have to have TIRE with good
yan path.
Tire with correct path will prevent the happening of symptom “aquaplanning” (loss of tire traction to asphalt).
Not merely just tire path which paid attention but also mount wear of tire, mount keausan of high tire will very dangerous.
Condition of slippery road street can result vehicle losing of traction and can result accident even death.
Following inspection tips at your vehicle tire :
* Tire path have to goodness, minimum is condition of tire 65%.
* Check tire wind pressure arrange according to manufacturer guide.
* Tire character have to as according to condition of road street, tire with specification of terrain mud (MT) very do not
recommend for the the rains of use tire with minimum specification of All Terrain (AT)
* If (there are) any surplus funds usage of special tire like wet tire will be more be peaceful. But tire manufacturer
technology now claim that their peaceful tire to be used at 2 season in Indonesia.
2. your Machine Vehicle need electrics entered to be can operate. Era now more than anything else.. already technology go
forward already.. cars arranged is same which is its name of ECU (module control elktronik).
But technological excess non meaning without insuffiency. You surely understand correctness that electricity component very
same susceptible which its name of water, like that with car, water can become riskiest cause at electricity system, can
result konslet.
Nature of water which is conductor earn konslet make vehicle key parts like ECU, Alternator etc. If have destroyed must case
most of these, changed by because is irreparable, price which is must redeemed costly fair to middling also.
For that before facing the rains you need to pay attention electricity system of your vehicle, especially part of following :
1. ECU, its costly price, don't to damage
2. CDI, way of its activity loo like ECU, its costly price also, don't to damage
3. Alternator, the heart of electricity system, costly fair to middling also its price
4. Coil, the heart of ignition system
5. Cable Spark plug and Spark plug, don'to wet
6. Accu / battery
7. Distributor
8. Irrigate Filter (air filter) can make hammer water (water enter into machine)
9. Carburettor
10. Injector
11. platinum
3. Go up car still rain… decrease to be decreased in the reality there is leaky, in the reality which become its ringleader
of door cover rubber which is already fragible. For that give attention of extra to the item rubber, change when needed, not
costly. Usually 1 priced door Rp 30-40.000
4. Cheque repeat the condition of wiper motor, wiper rubber and next glass of vehicle.
5. Check cooling system (AC) when rain. Interior can mist if AC not life, view to the fore become to turn tail.
6. Check elegibility of fog light (light fog)
So already at cheque repeat altogether, don't forget to play the game traffic keep distance peacefully of ride, and don't
forget to impose peacemaker belt.
***
Source : Translated from duniabengkel.com
Turn on Machine at the Morning
Still many people which of opinion car machine still need warm before road street, Yes or no the ascription..??
Basically in Indonesia climate is tropical climate (hot) though lately often floods and rain, but just remain to be of
Indonesia reside in [his/its] good tropis.Ada climate area [is] we [do/conduct] routine activity heat machine before road
street. This matter aim to to give opportunity at oil which still reside in below/under to go up and lubricate machine
component. Real correct it is true many oil manufacturer claim that oli they earn easily reach area which is lubrication need
swiftly but price can strangkle of neck, but make owner you enough budget rely on daily oil which snugly of the size your
sack bag, step heat machine before road street is best road street. To avoid wear of machine.
Following way of correct to heat morning machine :
1. Check the condition of radiator water every week
2. Animating machine (shake gas pedal 2-3 times making machine which still use carburetor, or draw cuk lever (choke)
3. Let aflame machine until temperature go up 1/3
4. At the same time temperature nunggu go up, from at stupefied you can check the condition of tire before leaving. Enough by
seeing it and give a little kick at tire to ascertain tire pressure snugly.
If have been reached by ideal temperature is you can leave to continue activity. Require to be also noticed by laboring
machine at ideal temperature will economize gasoline fuel consumption.
***
Source : Translated from duniabengkel.com
Basically in Indonesia climate is tropical climate (hot) though lately often floods and rain, but just remain to be of
Indonesia reside in [his/its] good tropis.Ada climate area [is] we [do/conduct] routine activity heat machine before road
street. This matter aim to to give opportunity at oil which still reside in below/under to go up and lubricate machine
component. Real correct it is true many oil manufacturer claim that oli they earn easily reach area which is lubrication need
swiftly but price can strangkle of neck, but make owner you enough budget rely on daily oil which snugly of the size your
sack bag, step heat machine before road street is best road street. To avoid wear of machine.
Following way of correct to heat morning machine :
1. Check the condition of radiator water every week
2. Animating machine (shake gas pedal 2-3 times making machine which still use carburetor, or draw cuk lever (choke)
3. Let aflame machine until temperature go up 1/3
4. At the same time temperature nunggu go up, from at stupefied you can check the condition of tire before leaving. Enough by
seeing it and give a little kick at tire to ascertain tire pressure snugly.
If have been reached by ideal temperature is you can leave to continue activity. Require to be also noticed by laboring
machine at ideal temperature will economize gasoline fuel consumption.
***
Source : Translated from duniabengkel.com
Economical of Clutch Canvas
Do you know old age Clutch Canvas (disc clutch) with normal usage can reach 4 years? How with your vehicle Clutch Canvas age..? How long you use your Clutch Canvas?
My friend tell age not possible to Clutch Canvas can as long as that… let us calculate with normal usage of vehicle in 1 year can pass through over 10.000km. meaning in 40.000km then we change the Clutch Canvas.
But in the reality there is which is on age 30.000km have changed Clutch Canvas.. why? Its answer not solely because quality of object but more at mistake during driving.
Following is small mistake which clip age wear Clutch Canvas during 1 year.
- Don'T depress pedal semi Clutch because accepted by burden is big Canvas, so that erod surface of Clutch Canvas, and result timeworn quickly. ordinary Mistake example of happened by using semi Clutch at the (time) of desisting red light in a state of climb.. better use hand rem and neutralize gear / transmission.
- Do transfer of transmission as smooth as possible, for example at the (time) of changing gear to go up (from gear 1 to gear 2 etc.) and or at the (time) of degrading gear (from gear 5 to gear 4 etc - Use transmission as according to speed of contained by vehicle at manual service book. Don'T use high gear at a speed of lowering. Example of which often happened is driver use gear 3 with speed only 30km/hour Try To comprehend elementary Concept following :
“Clutch Canvas used as by vehicle energy transfer from machine to wheel, non to arrest detain vehicle burden”
***
Source : Translated from duniabengkel.com
My friend tell age not possible to Clutch Canvas can as long as that… let us calculate with normal usage of vehicle in 1 year can pass through over 10.000km. meaning in 40.000km then we change the Clutch Canvas.
But in the reality there is which is on age 30.000km have changed Clutch Canvas.. why? Its answer not solely because quality of object but more at mistake during driving.
Following is small mistake which clip age wear Clutch Canvas during 1 year.
- Don'T depress pedal semi Clutch because accepted by burden is big Canvas, so that erod surface of Clutch Canvas, and result timeworn quickly. ordinary Mistake example of happened by using semi Clutch at the (time) of desisting red light in a state of climb.. better use hand rem and neutralize gear / transmission.
- Do transfer of transmission as smooth as possible, for example at the (time) of changing gear to go up (from gear 1 to gear 2 etc.) and or at the (time) of degrading gear (from gear 5 to gear 4 etc - Use transmission as according to speed of contained by vehicle at manual service book. Don'T use high gear at a speed of lowering. Example of which often happened is driver use gear 3 with speed only 30km/hour Try To comprehend elementary Concept following :
“Clutch Canvas used as by vehicle energy transfer from machine to wheel, non to arrest detain vehicle burden”
***
Source : Translated from duniabengkel.com
Way of Car Store
How to car store when do not be used during old ones.. for example you'd travel during more than 1 months, or possible you have antique car is darling which it is true become deposit.
Following is a few your which can automotive tips follow for the saving of darling car of you are later when wishing to be used remain to be prima in a condition.
1. Gasoline content until full, its intention is to take care of do not happened condensation from gasoline vapour able to result the happening of corrosion at gas tank.
2. Clean car, use plastic oli to protect car underside in order not to rust, bast vehicle to protect paint.
3. Park your garage car, don't draw hand rem..!! its intention is to prevent the happening of corrosion at rem because sufficient contact.
4. Use Jack stand, so that vehicle burden is not convergent at tire and velg.
5. Abstract Negative cable (-) Accu / battery meant in order not to there is current emiting a stream of during car do not be used. It is better to do electrocuting repeat accumulator when wishing to be re-used.
6. Kenalpot hole plug with cloth in order not to there is foreign particle entering, possible undesirable something else or mouse.
***
Source : Translated from duniabengkel.com
Following is a few your which can automotive tips follow for the saving of darling car of you are later when wishing to be used remain to be prima in a condition.
1. Gasoline content until full, its intention is to take care of do not happened condensation from gasoline vapour able to result the happening of corrosion at gas tank.
2. Clean car, use plastic oli to protect car underside in order not to rust, bast vehicle to protect paint.
3. Park your garage car, don't draw hand rem..!! its intention is to prevent the happening of corrosion at rem because sufficient contact.
4. Use Jack stand, so that vehicle burden is not convergent at tire and velg.
5. Abstract Negative cable (-) Accu / battery meant in order not to there is current emiting a stream of during car do not be used. It is better to do electrocuting repeat accumulator when wishing to be re-used.
6. Kenalpot hole plug with cloth in order not to there is foreign particle entering, possible undesirable something else or mouse.
***
Source : Translated from duniabengkel.com
Tips Buy Ex- Car
This time buy second hand car require to be careful many matter. Don'T get taken to buy its not car it the ex- the other insuffiency or collision. First which require to be checked by car body, its way by paying attention top-drawer car body angle,corner part of roof car machine, baggage, and door stanchion pillar.
Car which have collision have will seen there is handicap at part of above is mentioned, except replacement, if that way do not become problem. Check what is original still the car colour, by checked part of door rubber periphery and glass. equipment of Letter vehicle also very need and don't be disregarded in order not to generate the problem of with police government officer.
Wahoo… car you have get, step hereinafter beautify the the car to be not fail with new car. How To? You can bringing it to car salon closest, or correct reading tips from us following.
ex- Car disease (previous owner of not nice) usually dirty car interior. Cleaning, especially part of carpet and chair, use vacuum-cleaner to assist work. made seat materials from husk earn you clean by using baby shampoo and sponge.
Part of carpet car, paying attention what is damp carpet or not. If yes, hence that shares require to be unloaded later then made checked. Carpet from material of a kind wool, If suggested wet to change with newly. If not change, put to the sun bone dry carpet until.
Part of Plafond, use detergent to lift dirty stain which patch, later then mop until cleanness.
Part of car body in between by part of door, use comb make to clean dirt which patch.
Part of facia is lustrous, use special polish which which sold many marketing to be seen like newly again.
To clean car glass there is mushroom disappearance dilution to glass again shine.
Epilogue bast car body with drug bast which sold by many marketing your car return clean.
If you want to sale bmw for sale in houston i think good.
***
Source : Translated from duniabengkel.com
Car which have collision have will seen there is handicap at part of above is mentioned, except replacement, if that way do not become problem. Check what is original still the car colour, by checked part of door rubber periphery and glass. equipment of Letter vehicle also very need and don't be disregarded in order not to generate the problem of with police government officer.
Wahoo… car you have get, step hereinafter beautify the the car to be not fail with new car. How To? You can bringing it to car salon closest, or correct reading tips from us following.
ex- Car disease (previous owner of not nice) usually dirty car interior. Cleaning, especially part of carpet and chair, use vacuum-cleaner to assist work. made seat materials from husk earn you clean by using baby shampoo and sponge.
Part of carpet car, paying attention what is damp carpet or not. If yes, hence that shares require to be unloaded later then made checked. Carpet from material of a kind wool, If suggested wet to change with newly. If not change, put to the sun bone dry carpet until.
Part of Plafond, use detergent to lift dirty stain which patch, later then mop until cleanness.
Part of car body in between by part of door, use comb make to clean dirt which patch.
Part of facia is lustrous, use special polish which which sold many marketing to be seen like newly again.
To clean car glass there is mushroom disappearance dilution to glass again shine.
Epilogue bast car body with drug bast which sold by many marketing your car return clean.
If you want to sale bmw for sale in houston i think good.
***
Source : Translated from duniabengkel.com
PIT Stop to economize gasoline
Information following will very is assisting of you in ride security increase during ride, economical of fuel, as well as saving environment.
1. Take care of your car tire wind pressure, flat tire can destroy tire and make extravagantly of gasoline.
2. Check your wafting goods of car, degrading assumed wafting goods needn't. Burden Extra in car = gasoline extra also.
3. Avoid to race vehicle (pattern acceleration) drive good will very is having an in with of gasoline consumption. Try to reach highest tooth as soon as.
4. Avoid too old idle, for example if you await, better kill machine and alight from vehicle.
5. If possible avoid of jam, possible this hardest matter
6. Don'T accustom to put down foot at pedal put on the brakes or coupling pedal, because will result worn-out. putting down left foot at floor.
7. Check “sporing” tire, mistake of tire position will result tire quickly finished and is extravagant of gasoline.
8. Take care of car by routine service, to lessen contamination storey level to environment.
***
Source : Translated from duniabengkel.com
1. Take care of your car tire wind pressure, flat tire can destroy tire and make extravagantly of gasoline.
2. Check your wafting goods of car, degrading assumed wafting goods needn't. Burden Extra in car = gasoline extra also.
3. Avoid to race vehicle (pattern acceleration) drive good will very is having an in with of gasoline consumption. Try to reach highest tooth as soon as.
4. Avoid too old idle, for example if you await, better kill machine and alight from vehicle.
5. If possible avoid of jam, possible this hardest matter
6. Don'T accustom to put down foot at pedal put on the brakes or coupling pedal, because will result worn-out. putting down left foot at floor.
7. Check “sporing” tire, mistake of tire position will result tire quickly finished and is extravagant of gasoline.
8. Take care of car by routine service, to lessen contamination storey level to environment.
***
Source : Translated from duniabengkel.com
Change car paint will like people change clothes
Have you conceive, changing your car colour like you change clothes. If expense and amenity to change car colour as easy as that, surely progressively asyiik likely see darling car of you always respect and change colour as according to desire of is the vehicle owner. Momentarily such technology will immediately can enjoy for the you of which like to change paint colour, without decolorizing original paint of your car.
Have been found by car body colourant materials by Nissan Motor Group, conducive for the painting of and release of the colour coat without destroying original colour of vehicle body. With positive effect to protect original paint and also amenity like supposing play at to eliminate saturation surface of car arranged in layers by named cote "Miracle Cote". From other side amenity and is cheap of is expense of which is needed, this technology enable return of colour any time to original colour of car.
this Coting system have thick about 60 is micro metre, so that strong enough to protect original paint from light incision from bough, or tree rubber, and also sand serbuk or iron which possible incise at surface of car. With colour type in this time counted 22 colour, hence quite a lot colour choice which can be adapted for by wanted atmosphere.
this Coting construction consist of 3 coat, that is coat basis for most under, is then overlaped with last colour coat and also covered with transparent coat to protect against external incision. While original paint coat of itself car under elementary coat. this Elementary coat have function to take care of happened strong adhesion between coting with surface of car and also to heighten appearance of superimposed by colour coat above elementary coat.
this Technology Miracle Cote differ from ordinary painting which need emery process with sand paper. this Sequence Miracle Cote is started from:
# wash of Car to eliminate dirt.
# Draining from water which patch on the surface of.
# Coat wax omission, or oil above surface of original paint.
# Masking for hit by undesirable shares of coting.
# Process Coting from elementary coat, colour, last of transparency coat.
# Off Masking.
# Draining.
# Have.
Or return flaking of this simple enough coting, that is using special Iihat vitamin to discharge tying among elementary coat with original paint coat of car which use electrik jet-nozzle yielding positive ion.
Compound for the process of this basic flaking which react with carboxile molecule free from coting Iihat vitamin which finally form compound like dissolve soap in water. For the process of flaking of itself coting coat needed by time about 20 minute, and also finally is enough sprayed with branch water to throw away the the coat from car body. This process do not influence quality of original paint from itself car. And after finishing flaking process, hence mobilpun will return to its original colour.
Beside that coting coat which have been thrown the with additional treatment of additive will experience of cloting to be gathered by in storage base. Hereinafter is enough taken with ordinary filter, because this process do not entangle metal atom hence including friendly and peaceful process to environment.
For the prospect of this is technological future very fair and also is in this time strived to its cheap expense progressively even if in this time have semi from ordinary painting process. Colour metallic type or perl estimated during near by also will be able to be made. So that no wonder when in future, each month you can change your car colour swiftly as according to suasan which you wish. Leav at the post technological when this can enjoy in Indonesia.
***
Source : Translated from indoto.com
Have been found by car body colourant materials by Nissan Motor Group, conducive for the painting of and release of the colour coat without destroying original colour of vehicle body. With positive effect to protect original paint and also amenity like supposing play at to eliminate saturation surface of car arranged in layers by named cote "Miracle Cote". From other side amenity and is cheap of is expense of which is needed, this technology enable return of colour any time to original colour of car.
this Coting system have thick about 60 is micro metre, so that strong enough to protect original paint from light incision from bough, or tree rubber, and also sand serbuk or iron which possible incise at surface of car. With colour type in this time counted 22 colour, hence quite a lot colour choice which can be adapted for by wanted atmosphere.
this Coting construction consist of 3 coat, that is coat basis for most under, is then overlaped with last colour coat and also covered with transparent coat to protect against external incision. While original paint coat of itself car under elementary coat. this Elementary coat have function to take care of happened strong adhesion between coting with surface of car and also to heighten appearance of superimposed by colour coat above elementary coat.
this Technology Miracle Cote differ from ordinary painting which need emery process with sand paper. this Sequence Miracle Cote is started from:
# wash of Car to eliminate dirt.
# Draining from water which patch on the surface of.
# Coat wax omission, or oil above surface of original paint.
# Masking for hit by undesirable shares of coting.
# Process Coting from elementary coat, colour, last of transparency coat.
# Off Masking.
# Draining.
# Have.
Or return flaking of this simple enough coting, that is using special Iihat vitamin to discharge tying among elementary coat with original paint coat of car which use electrik jet-nozzle yielding positive ion.
Compound for the process of this basic flaking which react with carboxile molecule free from coting Iihat vitamin which finally form compound like dissolve soap in water. For the process of flaking of itself coting coat needed by time about 20 minute, and also finally is enough sprayed with branch water to throw away the the coat from car body. This process do not influence quality of original paint from itself car. And after finishing flaking process, hence mobilpun will return to its original colour.
Beside that coting coat which have been thrown the with additional treatment of additive will experience of cloting to be gathered by in storage base. Hereinafter is enough taken with ordinary filter, because this process do not entangle metal atom hence including friendly and peaceful process to environment.
For the prospect of this is technological future very fair and also is in this time strived to its cheap expense progressively even if in this time have semi from ordinary painting process. Colour metallic type or perl estimated during near by also will be able to be made. So that no wonder when in future, each month you can change your car colour swiftly as according to suasan which you wish. Leav at the post technological when this can enjoy in Indonesia.
***
Source : Translated from indoto.com
Treatment of Accu
Accu type is basically divided to become two kinds of that is : battery dry and battery wet. In this time have been developed by accu with indicator charge. By using indicator charge hence storey;level acidity of electrolyte dilution can know. Pursuant to its tension, accu used occasionally at vehicle divided to become 6 volt, 12 volt, and 24 volt. Accu can be used by some level start from 40 Ah-120 Ah.
Way of Taking care of Accu.
* Avoid accu from vibration, because accu very sensitive to vibration. Vibration can result plate in accu moult.
* Electrolyte dilution laboured don't less or more than size measure which have been specified. Plate don't which there are in undamped accu of electrolyte dilution. If the plate undamped dry and, hence can arise oxidation causing plate become to destroy. On the contrary if accu overfilled and bubble up can result damage of bodi component. Pressure irrigate abundant accu can result damage at accu house.
* Dilution electrolyte cheque with hydrometer to know do specific gravity dilution still as according to determined standard. If specific gravitying it have become one, dilution have to is immediately changed, because the dilution can electric saving current.
* Shall not use electrics energi redundantly because can lose weight electrolyte dilution type. If usage of electrics bigger than normal usage, better alternator and accu changed with larger ones capacities. Specific gravity accu will fixed equal to 1.26 if well-balanced usage.
***
Source : Translated from indoto.com
Way of Taking care of Accu.
* Avoid accu from vibration, because accu very sensitive to vibration. Vibration can result plate in accu moult.
* Electrolyte dilution laboured don't less or more than size measure which have been specified. Plate don't which there are in undamped accu of electrolyte dilution. If the plate undamped dry and, hence can arise oxidation causing plate become to destroy. On the contrary if accu overfilled and bubble up can result damage of bodi component. Pressure irrigate abundant accu can result damage at accu house.
* Dilution electrolyte cheque with hydrometer to know do specific gravity dilution still as according to determined standard. If specific gravitying it have become one, dilution have to is immediately changed, because the dilution can electric saving current.
* Shall not use electrics energi redundantly because can lose weight electrolyte dilution type. If usage of electrics bigger than normal usage, better alternator and accu changed with larger ones capacities. Specific gravity accu will fixed equal to 1.26 if well-balanced usage.
***
Source : Translated from indoto.com
Pump Acceleration Treatment
Vehicle you cannot better acceleration. Check your vehicle pump acceleration. First time you which must do to open air filter in front. Afterwards pay attention carburettor and pay attention fuel air stream hole.
If fuel empty into in venturi in gross mean your vehicle pump acceleration still. If scanty fuel stream mean vehicle pump acceleration there is problem.
Air filter in general there is two that is paper filter and oil filter type. To clean coherent dirt and dirt at paper filter enough by breeze air from side in by using compressor or of a kind. Can also used by dirt instrument to absorb to suck dirt at exterior. If dirt at inner air filter have thick and wet filter better change with newly. sweeping of Filter from dirt or dirt by continue require to be conducted by dirt sebelem or the dirt stick and difficult to be cleaned.
To clean air filter with oil can be conducted by taking filter element, last clean with gasoline. Afterwards fill its place with lubricating oil until height of surface of certain oil.
***
Source : Translated from indoto.com
If fuel empty into in venturi in gross mean your vehicle pump acceleration still. If scanty fuel stream mean vehicle pump acceleration there is problem.
Air filter in general there is two that is paper filter and oil filter type. To clean coherent dirt and dirt at paper filter enough by breeze air from side in by using compressor or of a kind. Can also used by dirt instrument to absorb to suck dirt at exterior. If dirt at inner air filter have thick and wet filter better change with newly. sweeping of Filter from dirt or dirt by continue require to be conducted by dirt sebelem or the dirt stick and difficult to be cleaned.
To clean air filter with oil can be conducted by taking filter element, last clean with gasoline. Afterwards fill its place with lubricating oil until height of surface of certain oil.
***
Source : Translated from indoto.com
BOX SPEAKER
As we know that to yield voice / good car audio it is of course we strive to be able to use all speaker type, Tweeter a.l yielding high frequency voice like percussion voice, fizz, without there is output voice bass.
Other Speaker is mid-range, yielding singer vowel voice following a little bass voice. Therefore both types of speaker the core important tweeter type, do not be needed by box / box which big so and can be put down wherever according to our will; desire direction, usually above facia or simply patch in door trim panel.
Last type is Sub-Woofer, we to study here, yielding low frequency only in the form of secretory bass voice. So that heard bass voice setle and is clear, better be made by special box. our Vehicle type, is Jeep type, MPV, salon sedan or Hatc-Back sedan and type / music stream which we take a fancy to ( jazz, rock, pop, classic, etc) it is of course follow to determine which better wear.
There is three speaker box form which one another have excess and insuffiency, y.i :
1. Box closed ( box sealed)
2. holey box ( box ported)
3. Aliance both ( Box Bandpass)
Box type closed.
Representing made easy and quickest/fastest box and also model / its for can be made is assorted. Big usually box / volume (in set of m3) have been determined and written by speaker each merk reference book. Its excess here, besides quickly and easy to making it, box this type of is not sensitive to made box volume inaccuracy. There is big difference of box 1 or 2 Cm, box sealed remain to still yield good voice. Its insuffiency is ability / its voice do not as hard as holey box (box ported) and still less at lowest frequency.
Holey box.
This type of given by ported / hole so that can be yield low frequency. long and Big of made ported influence yielded response frequency, thereby we earn to arrange its frequency response. If snugly making it, volume voice as small as, bass still heard by its excess oke. But that way there is its insuffiency that is this box very sensitive to mistake of measurement. A few volume difference by what instructed, its result very dissatisfactory. Once fail, unload box again. Besides weakness of this box to need compared to bigger place of box sealed. Don'T select/choose box this type of if spacious insufficient car room like Commercial type car / mpv.
Box Band-pass.
Box this type of aliance from both types of above. Usually one of the its side is endued with aklirik, as fashion, so that to be seen its it from outside. This type of likely there is box in box, given by ported / hole in one of the its side.
Its excess this type of can yield former compared to hardest bass voice both types of and its insuffiency is most difficult making it because its high.
Wrong once measure, bass voice can nope go out, but when snugly, best type box for the SPL OF. To a beginner which like jazz or classical, don't select/choose type box and time cleanseing many #
***
Source : Translated from indoto.com
Other Speaker is mid-range, yielding singer vowel voice following a little bass voice. Therefore both types of speaker the core important tweeter type, do not be needed by box / box which big so and can be put down wherever according to our will; desire direction, usually above facia or simply patch in door trim panel.
Last type is Sub-Woofer, we to study here, yielding low frequency only in the form of secretory bass voice. So that heard bass voice setle and is clear, better be made by special box. our Vehicle type, is Jeep type, MPV, salon sedan or Hatc-Back sedan and type / music stream which we take a fancy to ( jazz, rock, pop, classic, etc) it is of course follow to determine which better wear.
There is three speaker box form which one another have excess and insuffiency, y.i :
1. Box closed ( box sealed)
2. holey box ( box ported)
3. Aliance both ( Box Bandpass)
Box type closed.
Representing made easy and quickest/fastest box and also model / its for can be made is assorted. Big usually box / volume (in set of m3) have been determined and written by speaker each merk reference book. Its excess here, besides quickly and easy to making it, box this type of is not sensitive to made box volume inaccuracy. There is big difference of box 1 or 2 Cm, box sealed remain to still yield good voice. Its insuffiency is ability / its voice do not as hard as holey box (box ported) and still less at lowest frequency.
Holey box.
This type of given by ported / hole so that can be yield low frequency. long and Big of made ported influence yielded response frequency, thereby we earn to arrange its frequency response. If snugly making it, volume voice as small as, bass still heard by its excess oke. But that way there is its insuffiency that is this box very sensitive to mistake of measurement. A few volume difference by what instructed, its result very dissatisfactory. Once fail, unload box again. Besides weakness of this box to need compared to bigger place of box sealed. Don'T select/choose box this type of if spacious insufficient car room like Commercial type car / mpv.
Box Band-pass.
Box this type of aliance from both types of above. Usually one of the its side is endued with aklirik, as fashion, so that to be seen its it from outside. This type of likely there is box in box, given by ported / hole in one of the its side.
Its excess this type of can yield former compared to hardest bass voice both types of and its insuffiency is most difficult making it because its high.
Wrong once measure, bass voice can nope go out, but when snugly, best type box for the SPL OF. To a beginner which like jazz or classical, don't select/choose type box and time cleanseing many #
***
Source : Translated from indoto.com
EARLY IMPROVING ENERGY
Sometimes we confuse, machine vehicle of standard which have nicely its energy, but we still not yet satisfied also with its, habit...... human being do not always satisfy.
If us wish to improve energy with expense of cheapest, quickly and do not alter the specification of machine standard (darling possible because vehicle relative newly) can be conducted by several things with expense +/- Rp 1 to 2 million.
What we can do? Add its ignition energy !!
Change koil with specification of higher level ampere and tension thereby yielded energy will be more be big because sprinkling of bigger yielded fire.
In this way burnt easier fuel, our thankss also wear fuel with high octane and all ignition change with CDI systems. Nevertheless if tension too big nor good except when accompanied with spark plug replacement following its cable. If spark plug do not change, can melt and machine quickly heat.
For the ignition of modern machine, that is with ignition of coil multi systems (one spark plug one coil) or is semi of coil multi (two spark plug one coil), its replacement rather difficult because in this time no one have kompatibel as well as have do not be needed by spark plug cable again.
Then what earning us do modern mechanically which have the EFI? We still have opportunity with cheap expense and quickly, that is without altering ECU, we can enhance Fuel Regulator Adjustment apparatus on the chance of earning easily accomodate vehicle fuel pressure entered.
For the vehicle of with diesel fuel fuel, lightest is by adding apparatus a kind of accelerator diesel, etc.
***
Source : Translated from indoto.com
If us wish to improve energy with expense of cheapest, quickly and do not alter the specification of machine standard (darling possible because vehicle relative newly) can be conducted by several things with expense +/- Rp 1 to 2 million.
What we can do? Add its ignition energy !!
Change koil with specification of higher level ampere and tension thereby yielded energy will be more be big because sprinkling of bigger yielded fire.
In this way burnt easier fuel, our thankss also wear fuel with high octane and all ignition change with CDI systems. Nevertheless if tension too big nor good except when accompanied with spark plug replacement following its cable. If spark plug do not change, can melt and machine quickly heat.
For the ignition of modern machine, that is with ignition of coil multi systems (one spark plug one coil) or is semi of coil multi (two spark plug one coil), its replacement rather difficult because in this time no one have kompatibel as well as have do not be needed by spark plug cable again.
Then what earning us do modern mechanically which have the EFI? We still have opportunity with cheap expense and quickly, that is without altering ECU, we can enhance Fuel Regulator Adjustment apparatus on the chance of earning easily accomodate vehicle fuel pressure entered.
For the vehicle of with diesel fuel fuel, lightest is by adding apparatus a kind of accelerator diesel, etc.
***
Source : Translated from indoto.com
Colour Gas Throw Away
Knowing gas colour throw away to represent trivial matter but important as step early to know what is our good vehicle in a condition or do not. If gas throw away chromatic chromatic do not or a little is blue, can be ascertained by combustion take place goodness, because there are correct fuel mixture comparison. When gas throw away brown or rust colored, meaning fuel which follow in course of scanty combustion. If black chromatic show imperfect combustion process, because too much fuel which enter.
Gas throw away which is white chromatic will emerge if lubricating oil too much pouring into into room burn. This matter can be caused by damage at piston, piston ring, cylinder wall, spillway or take the air damage spillway. Or earn because of existence of leakage at packing-packing lead cylinder so that water can pour into into room burn.
Aqueous vapour that happened because combustion heat will seen exit together with gas throw away so that gas throw away white chromatic. But this matter can be differentiated by between white colour condense and turn white lubricating oil vapour. white Vapour chromatic lubricating oil and release aroma. In a state of is the vehicle still can be run, but usage of lubricating oil will become extravagantly.
Gas throw away black chromatic because of fuel mixture too rich air so that do not happened perfect combustion process. There are some possibility causing the the situation, for example air filter stuff up, air spillway closed or damage carburettor.
***
Source : Translated from indoto.com
Gas throw away which is white chromatic will emerge if lubricating oil too much pouring into into room burn. This matter can be caused by damage at piston, piston ring, cylinder wall, spillway or take the air damage spillway. Or earn because of existence of leakage at packing-packing lead cylinder so that water can pour into into room burn.
Aqueous vapour that happened because combustion heat will seen exit together with gas throw away so that gas throw away white chromatic. But this matter can be differentiated by between white colour condense and turn white lubricating oil vapour. white Vapour chromatic lubricating oil and release aroma. In a state of is the vehicle still can be run, but usage of lubricating oil will become extravagantly.
Gas throw away black chromatic because of fuel mixture too rich air so that do not happened perfect combustion process. There are some possibility causing the the situation, for example air filter stuff up, air spillway closed or damage carburettor.
***
Source : Translated from indoto.com
Subscribe to:
Posts (Atom)